Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › THEFT DETERRENT SYSTEM › 2012.03–2020.08
RM2070E _58 Vehicle Interior _061938 THEFT DETERRENT / KEYLESS ENTRY _0301770 THEFT DETERRENT SYSTEM C

THEFT DETERRENT / KEYLESS ENTRY  THEFT DETERRENT SYSTEM  B2762  Intrusion Sensor Signal Circuit Malfunction  


DESCRIPTION

The intrusion sensor (theft warning ultrasonic sensor) (map light assembly) conducts self-diagnosis immediately after power is supplied to the sensor (when the theft deterrent system is set).

If a malfunction is detected in the ISIF line, the main body ECU (multiplex network body ECU) stores this DTC.


DTC No. DTC Detection Condition Trouble Area
B2762 After normal/trouble signal is output from intrusion sensor as result of self-diagnosis, following malfunctions are detected:
1.

ISIF line circuit is open

2.

Reception of signals other than normal/trouble signal


·

Intrusion sensor (theft warning ultrasonic sensor) (map light assembly)

·

Main body ECU (multiplex network body ECU)

·

Wire harness or connector



WIRING DIAGRAM

B220569E17
1.933,3.051 3.206,3.190 1.272,0.139 10 Map Light Assembly 5.385,2.948 7.030,3.254 1.645,0.306 10 Main Body ECU (Multiplex Network Body ECU) 2.053,1.338 3.220,1.820 1.167,0.482 10 Intrusion Sensor (Theft Warning Ultrasonic Sensor) 3.545,1.469 3.816,1.606 0.271,0.137 10 +B2 3.47,2.029 3.820,2.168 0.350,0.139 10 IOUT 1.382,1.665 1.787,1.802 0.404,0.137 10 GND1 1.933,2.911 2.139,3.050 0.206,0.139 10 U3 5.628,1.56 6.031,1.697 0.403,0.137 10 BECU 5.628,2.127 5.901,2.266 0.274,0.138 10 ISIF 3.911,1.469 4.087,1.606 0.176,0.137 10 12 3.911,2.029 4.086,2.167 0.175,0.137 10 13 5.323,1.371 5.500,1.509 0.177,0.138 10 30 5.323,1.931 5.500,2.069 0.177,0.137 10 12 5.298,1.56 5.524,1.698 0.226,0.138 10 MB 1.108,1.665 1.285,1.803 0.177,0.138 10 15 5.326,2.127 5.501,2.266 0.174,0.139 10 L8 4.064,0.243 5.410,0.387 1.346,0.144 10 from Auxiliary Battery

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MAP LIGHT ASSEMBLY)
a.

Disconnect the L8 main body ECU (multiplex network body ECU) connector.


b.

Disconnect the U3 map light assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L8-12 (ISIF) - U3-13 (IOUT) Always Below 1 Ω




OK

2.REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (MAP LIGHT ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.REPLACE INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (MAP LIGHT ASSEMBLY)
a.

Replace the intrusion sensor (theft warning ultrasonic sensor) (map light assembly) (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).



NEXT

3.CHECK FOR DTC
3.CHECK FOR DTC

b.

Turn the power switch on (IG), then off.


c.

Set the theft deterrent system to "ARMED STATE".


d.

Check that the security indicator changes from illuminated to blinking.


e.

Set the theft deterrent system to "DISARMED STATE".


f.


OK

END (INTRUSION SENSOR (THEFT WARNING ULTRASONIC SENSOR) (MAP LIGHT ASSEMBLY) WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)