Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061939 LIGHTING (INT) _0301790 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Interior Light Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the operation of the following lights:

·

Map light assembly

·

No. 1 room light assembly


HINT:

The light cut relay supplies power to the lights not controlled by the illuminated entry system. If all of the lights that use power from the light cut relay do not turn on, check the light cut relay circuit first (See page Vehicle Interior>LIGHTING (INT)>LIGHTING SYSTEM>PROBLEM SYMPTOMS TABLE).


WIRING DIAGRAM

E306617E05
3.24,3.01 3.49,3.188 0.25,0.177 10 false ON 2.302,3.01 2.552,3.188 0.25,0.177 10 false ON 2.302,4.448 2.552,4.625 0.25,0.177 10 false ON 4.198,4.448 4.417,4.625 0.219,0.177 10 false 15 4.198,4.052 4.417,4.229 0.219,0.177 10 false 10 0.25,2.552 0.448,2.729 0.198,0.177 10 false 11 0.875,6.896 1,7.073 0.125,0.177 10 false B 0.646,5.969 0.771,6.146 0.125,0.177 10 false B 2.365,7.094 2.5,7.271 0.135,0.177 10 false E 2.552,6.698 2.656,6.875 0.104,0.177 10 false 3 2.552,7.094 2.656,7.271 0.104,0.177 10 false 2 4.198,2.188 4.542,2.354 0.344,0.167 10 false 6*1 4.01,4.052 4.135,4.229 0.125,0.177 10 false E 2.781,6.208 2.948,6.385 0.167,0.177 10 false 7 0.688,6.896 0.802,7.073 0.115,0.177 10 false 1 0.646,6.208 0.781,6.385 0.135,0.177 10 false 1 3.146,0.448 4.896,0.688 1.75,0.24 10 false from Light Cut Relay 2.781,5.969 3.188,6.146 0.406,0.177 10 false DCTY 3.115,6.219 3.521,6.396 0.406,0.177 10 false U3 3.74,4.448 4.167,4.625 0.427,0.177 10 false GND1 3.427,2.615 3.875,2.792 0.448,0.177 10 false DOOR 2.188,6.698 2.49,6.875 0.302,0.177 10 false CTY 1.594,6.625 2.073,6.802 0.479,0.177 10 false DOOR 1.823,7.313 2.094,7.49 0.271,0.177 10 false ON 3.844,2.365 4.156,2.542 0.313,0.177 10 false CTY 0.479,2.552 0.771,2.729 0.292,0.177 10 false +B1 3.24,1.969 3.563,2.146 0.323,0.177 10 false OFF 2.302,2.365 2.615,2.542 0.313,0.177 10 false OFF 2.302,4.833 2.635,5.01 0.333,0.177 10 false OFF 1.542,5.125 2.479,5.469 0.938,0.344 10 false Personal Light Switch RH 5.917,2.302 6.042,2.479 0.125,0.177 10 false 1 5.875,2.49 6.115,2.667 0.24,0.177 10 false MB 4.771,2.49 5.01,2.667 0.24,0.177 10 false 2A 6.292,2.49 6.573,2.667 0.281,0.177 10 false ILE 4.771,2.292 4.948,2.469 0.177,0.177 10 false 52 4.542,2.854 6.188,3.188 1.646,0.333 10 false Instrument Panel Junction Block Assembly 1.542,3.302 2.448,3.646 0.906,0.344 10 false Personal Light Switch LH 0.729,2.302 2.052,2.458 1.323,0.156 10 false Front Dome Light LH 2.469,1.51 4.063,1.667 1.594,0.156 10 false Interior Light Door Switch 0.729,4.385 2.125,4.542 1.396,0.156 10 false Front Dome Light RH 0.802,7.771 1.115,7.927 0.313,0.156 10 false U10 0.802,7.927 2.563,8.083 1.76,0.156 10 false No. 1 Room Light Assembly 5.438,7.365 7.104,7.708 1.667,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 3.115,6.375 4.552,6.625 1.438,0.25 10 false Map Light Assembly 4.198,2.354 4.542,2.521 0.344,0.167 10 false 16*2 2.917,8.323 3.781,8.521 0.865,0.198 10 false *1: for LHD 3.958,8.323 4.823,8.521 0.865,0.198 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the lights operate.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Illuminated Entry System Personal light and No. 1 room light assembly ON/OFF Interior light door switch on and all doors closed

OK:

Each light fades in.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT MAP LIGHT ASSEMBLY
2.INSPECT MAP LIGHT ASSEMBLY
a.

Remove the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL).


b.

Inspect the map light assembly (See page Vehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>INSPECTION).


OK:

Map light assembly is normal.



OK

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPLACE MAP LIGHT ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (MAP LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2A instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U3-6 (CTY) - 2A-52*1 Always Below 1 Ω
U3-6 (CTY) - Body ground*1 Always 10 kΩ or higher
U3-16 (CTY) - 2A-52*2 Always Below 1 Ω
U3-16 (CTY) - Body ground*2 Always 10 kΩ or higher


*1: for LHD

*2: for RHD




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
U155074E01
0.191,0.138 0.385,0.284 0.194,0.145 10 *a 1.582,0.757 1.769,0.938 0.187,0.181 10 2A 1.551,3.111 1.808,3.293 0.257,0.181 10 MB 0.361,4.044 0.593,4.195 0.232,0.151 10 ILE 0.272,3.623 0.464,4.023 false

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-52 - MB-1 (ILE) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY