Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2070E _58 Vehicle Interior _061939 LIGHTING (INT) _0301790 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Front Door Courtesy Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the front door courtesy light switch using this circuit.

WIRING DIAGRAM

E244217E02
5.75,1.146 5.854,1.292 0.104,0.146 10 false 2 5.688,1.344 5.917,1.49 0.229,0.146 10 false MB 5.688,2.458 5.917,2.604 0.229,0.146 10 false MB 5.74,2.26 5.854,2.406 0.115,0.146 10 false 4 6.031,1.344 6.438,1.521 0.406,0.177 10 false FLCY 6.031,2.469 6.438,2.646 0.406,0.177 10 false FRCY 0.938,1.479 1.25,1.656 0.313,0.177 10 false R6 0.938,2.594 1.229,2.771 0.292,0.177 10 false S5 0.938,1.625 4,1.885 3.063,0.26 10 false Front Door Courtesy Light Switch Assembly LH 0.938,2.75 3.969,2.969 3.031,0.219 10 false Front Door Courtesy Light Switch Assembly RH 4.51,1.167 4.74,1.333 0.229,0.167 10 false 35 4.5,1.354 4.729,1.531 0.229,0.177 10 false 2D 4.51,2.25 4.74,2.417 0.229,0.167 10 false 36 4.5,2.448 4.729,2.625 0.229,0.177 10 false 2D 3.052,1.24 3.219,1.417 0.167,0.177 10 false 1 3.052,2.24 3.219,2.417 0.167,0.177 10 false 1 5.438,3.646 7.104,3.979 1.667,0.333 10 false Main Body ECU (Multiplex Network Body ECU) 4.323,2.792 5.99,3.115 1.667,0.323 10 false Instrument Panel Junction Block Assembly

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
FR Door Courtesy SW Front door courtesy light switch RH signal/ON or OFF ON: Front door RH open
OFF: Front door RH closed
-
FL Door Courtesy SW Front door courtesy light switch LH signal/ON or OFF ON: Front door LH open
OFF: Front door LH closed
-

OK:

Normal conditions listed above are displayed.



Result:
Result Proceed to
OK A
Front door courtesy light switch LH or RH does not operate B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
2.INSPECT FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY (LH OR RH)
a.

Remove the front door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>REMOVAL).


b.

Inspect the front door courtesy light switch assembly (See page Vehicle Interior>LIGHTING (INT)>FRONT DOOR COURTESY SWITCH>INSPECTION).

OK:

Front door courtesy light switch assembly is normal.




OK

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)

NG

REPLACE FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - FRONT DOOR COURTESY LIGHT SWITCH ASSEMBLY)
a.

for Front LH

i.

Disconnect the 2D instrument panel junction block assembly connector.


ii.

Disconnect the R6 front door courtesy light switch assembly LH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-35 - R6-1 Always Below 1 Ω
2D-35 - Body ground Always 10 kΩ or higher




b.

for Front RH

i.

Disconnect the 2D instrument panel junction block assembly connector.


ii.

Disconnect the S5 front door courtesy light switch assembly RH connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-36 - S5-1 Always Below 1 Ω
2D-36 - Body ground Always 10 kΩ or higher





OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
U155044E03
0.333,3.604 0.333,4.167 false 1.573,2.906 1.813,3.063 0.24,0.156 10 false MB 0.146,0.177 0.406,0.365 0.26,0.188 10 false *a 1.552,0.354 1.833,0.51 0.281,0.156 10 false 2D 0.146,4.188 0.563,4.385 0.417,0.198 10 false FLCY

for Front LH

i.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


ii.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-35 - MB-2 (FLCY) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



b.
U155045E03
0.521,3.604 0.521,4.177 false 1.573,2.906 1.802,3.063 0.229,0.156 10 false MB 0.146,0.177 0.406,0.365 0.26,0.188 10 false *a 1.552,0.354 1.833,0.51 0.281,0.156 10 false 2D 0.292,4.198 0.771,4.448 0.479,0.25 10 false FRCY

for Front RH

i.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


ii.

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2D-36 - MB-4 (FRCY) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY