Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM
RM2070E _58 Vehicle Interior _061939 LIGHTING (INT) _0301790 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Footwell Light Circuit  


DESCRIPTION

The main body ECU (multiplex network ECU) controls the footwell lights.

WIRING DIAGRAM

E229437E07
2.083,0.385 3.427,0.552 1.344,0.167 10 false from Auxiliary Battery 5.656,0.833 5.833,1 0.177,0.167 10 false 26 4.49,0.833 4.667,1 0.177,0.167 10 false 17 4.479,1.031 4.677,1.198 0.198,0.167 10 false 2B 4.49,2.615 4.688,2.781 0.198,0.167 10 false 2B 5.625,1.031 5.865,1.198 0.24,0.167 10 false MB 4.49,2.417 4.667,2.583 0.177,0.167 10 false 18 5.99,1.021 6.385,1.188 0.396,0.167 10 false FSPT 0.896,1.708 3.688,2.021 2.792,0.313 10 false No. 1 Interior Illumination Light Assembly RH (Footwell Light) 0.896,3.281 3.698,3.594 2.802,0.313 10 false No. 1 Interior Illumination Light Assembly LH (Footwell Light) 4.292,2.969 5.938,3.281 1.646,0.313 10 false Instrument Panel Junction Block Assembly 5.469,3.792 7.115,4.104 1.646,0.313 10 false Main Body ECU (Multiplex Network Body ECU) 0.813,0.552 1.25,0.719 0.438,0.167 10 false DOME 0.896,1.531 1.417,1.688 0.521,0.156 10 false L158*2 1.365,0.948 1.479,1.094 0.115,0.146 10 false 2 1.51,0.948 1.625,1.094 0.115,0.146 10 false B 1.365,2.521 1.479,2.667 0.115,0.146 10 false 2 1.51,2.521 1.625,2.667 0.115,0.146 10 false B 2.792,2.521 2.906,2.667 0.115,0.146 10 false L 2.938,2.521 3.052,2.667 0.115,0.146 10 false 1 2.792,0.927 2.906,1.073 0.115,0.146 10 false L 2.938,0.938 3.052,1.083 0.115,0.146 10 false 1 0.896,3.104 1.427,3.26 0.531,0.156 10 false L159*2 0.896,1.365 1.396,1.51 0.5,0.146 10 false L1*1 0.896,2.958 1.427,3.115 0.531,0.156 10 false L77*1 1.594,4.104 2.365,4.26 0.771,0.156 10 false *2: for RHD 0.604,4.104 1.427,4.302 0.823,0.198 10 false *1: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect fuses for circuits related to this system before performing the following inspection procedure.

·

Check that the light intensity of the light control rheostat is set to maximum.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the footwell lights come on.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Fr Foot Light Footwell lights ON/OFF Precondition for using the Active Test to turn lights on and off:
·

Power switch is turned off just before performing the Active Test.



OK:

Footwell lights come on.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY)
a.

for Front LH

i.

Disconnect the L77*1 or L159*2 No. 1 interior illumination light assembly LH (footwell light) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L77-2 (B) - Body ground*1 Power switch off 11 to 14 V
L159-2 (B) - Body ground*2 Power switch off 11 to 14 V




b.

for Front RH

i.

Disconnect the L1*1 or L158*2 No. 1 interior illumination light assembly RH (footwell light) connector.


ii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L1-2 (B) - Body ground*1 Power switch off 11 to 14 V
L158-2 (B) - Body ground*2 Power switch off 11 to 14 V




*1: for LHD

*2: for RHD



OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

for Front LH

i.

Disconnect the 2B instrument panel junction block assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L77-1 (L) - 2B-18*1 Always Below 1 Ω
L77-1 (L) - Body ground*1 Always 10 kΩ or higher
L159-1 (L) - 2B-18*2 Always Below 1 Ω
L159-1 (L) - Body ground*2 Always 10 kΩ or higher




b.

for Front RH

i.

Disconnect the 2B instrument panel junction block assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L1-1 (L) - 2B-17*1 Always Below 1 Ω
L1-1 (L) - Body ground*1 Always 10 kΩ or higher
L158-1 (L) - 2B-17*2 Always Below 1 Ω
L158-1 (L) - Body ground*2 Always 10 kΩ or higher




*1: for LHD

*2: for RHD



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.
U155046E02
1.69,0.819 1.885,1.000 0.195,0.181 10 2B 0.135,0.094 0.332,0.255 0.198,0.161 10 *a 1.696,2.91 1.934,3.091 0.238,0.181 10 MB 2.469,3.838 2.926,3.999 0.457,0.161 10 FSPT 2.652,3.469 2.652,3.83 false

Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2B-17 - MB-26 (FSPT) Always Below 1 Ω
2B-18 - MB-26 (FSPT) Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY