Home › Vehicle Interior › LIGHTING (INT) › LIGHTING SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061939 LIGHTING (INT) _0301790 LIGHTING SYSTEM J

LIGHTING (INT)  LIGHTING SYSTEM  Power Switch Illumination Circuit  


DESCRIPTION

The illuminated entry system controls the power switch illumination.

WIRING DIAGRAM

E309266E61
3.271,0.698 3.885,0.896 0.615,0.198 10 false SWIL 3.229,1.323 3.844,1.521 0.615,0.198 10 false AGND 3.75,0.698 3.906,0.896 0.156,0.198 10 false 9 3.75,1.323 3.906,1.521 0.156,0.198 10 false 6 4.802,0.698 5.115,0.896 0.313,0.198 10 false 16 4.802,1.323 5.115,1.521 0.313,0.198 10 false 24 4.781,1.969 5.24,2.167 0.458,0.198 10 false L197 5.073,0.698 5.688,0.896 0.615,0.198 10 false SWIL 5.073,1.323 5.688,1.521 0.615,0.198 10 false AGND 1.771,2 2.229,2.198 0.458,0.198 10 false L194 1.771,2.156 3.604,2.354 1.833,0.198 10 false Power Switch 4.771,2.135 6.583,2.615 1.813,0.479 10 false Certification ECU (Smart Key ECU Assembly) 5.906,0.667 6.219,0.865 0.313,0.198 10 false +B

CAUTION / NOTICE / HINT

NOTICE:

Check that the light intensity of the light control rheostat is set to maximum.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Entry&Start / Active Test.


e.

Check that the illumination operates.

Entry&Start
Tester Display Test Part Control Range Diagnostic Note
Power/Engine SW Light Power switch light ON/OFF When performing this Active Test, make sure the following condition is met:
The power switch illumination is off (15 seconds or more have elapsed since it turned from on to off) and the power switch is on (ACC) or on (IG), or the hybrid control system is running.

OK:

Power switch illumination comes on.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT POWER SWITCH
2.INSPECT POWER SWITCH

b.

Inspect the power switch (See page Engine / Hybrid System>2ZR-FXE (STARTING)>POWER SWITCH>INSPECTION).

OK:

Power switch illumination comes on.




OK

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))

NG

3.CHECK HARNESS AND CONNECTOR (POWER SWITCH - CERTIFICATION ECU (SMART KEY ECU ASSEMBLY))
a.

Disconnect the L197 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the L194 power switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L194-9 (SWIL) - L197-16 (SWIL) Always Below 1 Ω
L194-6 (AGND) - L197-24 (AGND) Always Below 1 Ω
L194-9 (SWIL)orL197-16 (SWIL) - Body ground Always 10 kΩ or higher
L194-6 (AGND)orL197-24 (AGND) - Body ground Always 10 kΩ or higher




OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR