Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Malfunction in Water Temperature Warning Light  


DESCRIPTION

In this circuit, the combination meter sub-assembly receives engine coolant temperature signals from the ECM using the CAN communication system. The combination meter sub-assembly displays engine coolant temperature warnings based on the data received from the ECM.

WIRING DIAGRAM

E156127E62
0.802,1.552 1.135,1.698 0.333,0.146 10 false THW 0.708,2.125 1.208,2.271 0.5,0.146 10 false ETHW 1.208,2.01 1.531,2.167 0.323,0.156 10 false 65 1.188,1.417 1.365,1.573 0.177,0.156 10 false 64 1.75,3.385 4.615,3.521 2.865,0.135 10 false : CAN Communication Line 2.177,2.479 2.469,2.635 0.292,0.156 10 false D6 5.042,3.125 7.156,3.448 2.115,0.323 10 false Combination Meter Sub-assembly (Meter Circuit Plate) 3.146,2.021 3.323,2.177 0.177,0.156 10 false 2 2.125,2.021 2.302,2.177 0.177,0.156 10 false 1 2.177,2.625 3.521,2.969 1.344,0.344 10 false Engine Coolant Temperature Sensor 0.573,3.292 0.938,3.458 0.365,0.167 10 false ECM 0.573,3.135 0.906,3.313 0.333,0.177 10 false D28

CAUTION / NOTICE / HINT

HINT:
·

If there is an open or short in the engine coolant temperature sensor circuit, the ECM stores the DTCs. Troubleshoot the SFI system (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).

·

If the exhaust heat recirculation system has a malfunction, the water temperature warning light comes on to inform the driver of the malfunction.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B




A

2.SYSTEM CHECK

B

2.SYSTEM CHECK
a.

Check the Water temperature warning light.

Result:
Result Proceed to
Water temperature warning light does not come on. A
Water temperature warning light remains on. B




A

3.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP COOLANT HOT)

B

4.CHECK FOR DTC
3.PERFORM ACTIVE TEST USING GTS (INDICAT. LAMP COOLANT HOT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the operation by referring to the table below.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Lamp Coolant Hot Water temperature warning light OFF or ON -

OK:

Water temperature warning light operation is normal.




OK

4.CHECK FOR DTC

NG

4.CHECK FOR DTC
a.

Check for DTCs (See page Engine / Hybrid System>2ZR-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR for SFI System, Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR for Meter/Gauge System).

Result:
Result Proceed to
DTC is not output. A
DTC of SFI system is output. B
DTC B1503 is output. C




A

5.READ VALUE USING GTS (COOLANT TEMPERATURE, COOLANT TEMP)

B

C

5.READ VALUE USING GTS (COOLANT TEMPERATURE, COOLANT TEMP)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus:

i.

for Combination Meter: Body Electrical / Combination Meter / Data List.


ii.

for Engine: Powertrain / Engine and ECT / Data List.



e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Coolant Temperature Engine coolant temperature / 0 to 127.5°C (0 to 261.5°F) After warming up: 75 to 100°C (167 to 212°F) -

Engine and ECT
Tester Display Measurement Item/Range Normal Condition Stored as Freeze Frame Data
Coolant Temp Engine coolant temperature/
Min.: -40°C (-40°F), Max.: 140°C (284°F)
75 to 100°C (167 to 212°F): After warming up Yes
Diagnostic Note:
This is the engine coolant temperature.
HINT:
·

After warming up the engine, the engine coolant temperature is 75 to 100°C (167 to 212°F).

·

After a long soak, the engine coolant temperature, intake air temperature and ambient air temperature are approximately equal.

·

If the value is -40°C (-40°F) or higher than 135°C (275°F), the sensor circuit may be open or shorted.

·

Check if the engine overheats when the value indicates higher than 135°C (275°F).




NOTICE:

Enter inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


Result:
Result Proceed to
The data list values of the ECUs do not match. A
The data list values of the ECUs match. B


HINT:

When the Data List values of the ECUs do not match, a signal output error of the ECM is suspected.




A

6.REPLACE METER CIRCUIT PLATE

B

6.REPLACE METER CIRCUIT PLATE
a.

Replace the meter circuit plate with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY).

OK:

The operation of the water temperature warning light returns to normal.




OK

END

NG