Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Meter Illumination is Always Dark  


DESCRIPTION

The combination meter sub-assembly receives signals from this circuit to adjust the illumination of the meter. The combination meter sub-assembly sets the illumination level based on the user operation of the light control rheostat switch.

HINT:
·

The meter illumination level can be adjusted by operating the hazard warning signal switch assembly (light control rheostat switch).

·

The meter illumination dims when the light control switch is turned to the tail, head, or AUTO position at night.

·

Setting the meter illumination to maximum brightness cancels the above dimming of the meter illumination.



WIRING DIAGRAM

E165892E37
3.561,3.063 3.809,3.220 0.248,0.157 10 I1 1.634,1.514 1.812,1.656 0.179,0.142 10 20 1.634,2.072 1.820,2.214 0.186,0.142 10 22 1.634,2.628 1.809,2.770 0.175,0.142 10 21 3.433,1.516 3.530,1.658 0.097,0.142 10 3 3.433,2.074 3.539,2.216 0.106,0.142 10 6 3.433,2.628 3.536,2.770 0.103,0.142 10 4 1.19,1.607 1.563,1.749 0.373,0.142 10 CLTB 1.19,2.177 1.563,2.319 0.373,0.142 10 CLTE 1.19,2.747 1.563,2.889 0.373,0.142 10 CLTS 3.641,1.609 4.015,1.751 0.373,0.142 10 CLTB 3.641,2.179 4.015,2.321 0.373,0.142 10 CLTE 3.641,2.721 4.015,2.863 0.373,0.142 10 CLTS 1.394,4.107 4.301,4.291 2.906,0.184 10 : CAN Communication Line 3.8,0.412 6.703,0.569 2.903,0.157 10 to each part that uses the dimmer signal 0.658,3.2 0.939,3.358 0.281,0.158 10 L7 3.552,3.23 4.782,3.607 1.230,0.378 10 Automatic Light Control Sensor 0.658,3.352 2.333,3.688 1.674,0.336 10 Main Body ECU (Multiplex Network Body ECU) 5.019,3.226 7.140,3.562 2.121,0.336 10 Combination Meter Sub-assembly (Meter Circuit Plate)

CAUTION / NOTICE / HINT

HINT:

Before starting the following inspection, check if the lighting system outputs DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication DTCs are output (See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

Result:
Result Proceed to
CAN communication DTCs are not output. A
CAN communication DTCs are output. B




A

2.READ VALUE USING GTS (ILLUMINATION RATE INFO)

B

2.READ VALUE USING GTS (ILLUMINATION RATE INFO)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Check the values by referring to the table below.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate Info Illumination rate information/0 ms. to 99.99 ms. Value output according to ambient light level -

Result:
Result Proceed to
The output value changes according to the ambient light level. A
The output value does not change according to the ambient light level. B




A

3.REPLACE METER CIRCUIT PLATE

B

CHECK CUSTOMIZE PARAMETER SETTING (SENSITIVITY)

3.REPLACE METER CIRCUIT PLATE
a.

Replace the meter circuit plate with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY).

OK:

The operation of the combination meter sub-assembly returns to normal.




OK

END

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)