Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Headup Display Malfunction  


DESCRIPTION

The headup display system displays some vehicle information on the windshield glass.

The headup display system consists of the combination mirror meter ECU and combination meter sub-assembly.

The combination mirror meter ECU receives information from the combination meter sub-assembly via communication and projects it on the windshield.

WIRING DIAGRAM

E251608E03
3.333,0.781 4.385,0.969 1.052,0.188 10 false from Each ECU 5.531,0.365 5.75,0.552 0.219,0.188 10 false 19 5.531,0.938 5.75,1.125 0.219,0.188 10 false 20 5.604,1.594 5.75,1.781 0.146,0.188 10 false 1 5.604,2.167 5.75,2.354 0.146,0.188 10 false 7 5.604,2.74 5.75,2.927 0.146,0.188 10 false 8 5.604,3.333 5.75,3.521 0.146,0.188 10 false 9 5.531,3.906 5.792,4.094 0.26,0.188 10 false 10 5.531,4.479 5.792,4.667 0.26,0.188 10 false 12 4.521,1.594 4.667,1.781 0.146,0.188 10 false 1 4.521,2.167 4.667,2.354 0.146,0.188 10 false 3 4.521,2.74 4.667,2.927 0.146,0.188 10 false 4 4.521,3.333 4.667,3.521 0.146,0.188 10 false 5 4.521,3.906 4.781,4.094 0.26,0.188 10 false 6 4.521,4.479 4.781,4.667 0.26,0.188 10 false 8 5.771,4.594 6.135,4.781 0.365,0.188 10 false GND 5.771,4.021 6.135,4.208 0.365,0.188 10 false SIL 5.771,3.448 6.135,3.635 0.365,0.188 10 false SIH 5.771,2.854 6.135,3.042 0.365,0.188 10 false TX- 5.771,2.281 6.135,2.469 0.365,0.188 10 false TX+ 5.771,1.698 6.135,1.885 0.365,0.188 10 false 12V 4.104,4.594 4.469,4.781 0.365,0.188 10 false GND 4.167,2.854 4.531,3.042 0.365,0.188 10 false SIL 4.167,2.281 4.531,2.469 0.365,0.188 10 false SIH 4.146,4.021 4.51,4.208 0.365,0.188 10 false TX- 4.146,3.448 4.51,3.635 0.365,0.188 10 false TX+ 4.146,1.698 4.51,1.885 0.365,0.188 10 false 12V 3.458,2.635 3.948,2.823 0.49,0.188 10 false HUDU 3.458,3.823 3.948,4.01 0.49,0.188 10 false HUDO 3.458,4.313 3.677,4.5 0.219,0.188 10 false E 3.198,4.198 3.417,4.385 0.219,0.188 10 false 16 3.198,3.719 3.417,3.906 0.219,0.188 10 false 15 3.198,2.521 3.417,2.708 0.219,0.188 10 false 14 2.417,4.198 2.635,4.385 0.219,0.188 10 false 1 2.417,3.719 2.635,3.906 0.219,0.188 10 false 4 2.417,2.521 2.635,2.708 0.219,0.188 10 false 3 2.208,4.198 2.427,4.385 0.219,0.188 10 false E 0.948,3.99 1.385,4.177 0.438,0.188 10 false HUD 0.25,4.979 0.688,5.167 0.438,0.188 10 false L147 0.25,5.135 2.406,5.323 2.156,0.188 10 false Headup Display Switch Assembly 5.656,4.969 6.094,5.156 0.438,0.188 10 false L141 5.656,5.135 6.865,5.531 1.208,0.396 10 false Combination Meter Sub-assembly 1.146,6.198 2.948,6.385 1.802,0.188 10 false : CAN Communication Line 2.99,4.896 3.427,5.083 0.438,0.188 10 false L149 2.99,5.042 4.906,5.448 1.917,0.406 10 false Headup Display (Combination Meter Mirror ECU) 0.948,2.781 1.385,2.969 0.438,0.188 10 false SET 2.115,3.719 2.385,3.906 0.271,0.188 10 false CH 2,2.521 2.375,2.708 0.375,0.188 10 false NVM 5.771,1.094 6.208,1.281 0.438,0.188 10 false CANL 5.771,0.521 6.208,0.708 0.438,0.188 10 false CANH

CAUTION / NOTICE / HINT

HINT:

Before starting the following inspection, confirm the headup display position and illuminance, then perform the on-vehicle inspection (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION).


PROCEDURE

1.SYSTEM CHECK
a.

Check the symptom of the headup display.

Result:
Result Proceed to
Headup display does not display at all. A
Display of the headup display is abnormal. B




A

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - BODY GROUND)

B

5.SYSTEM CHECK
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - BODY GROUND)
a.
U191225E01
1.576,0.776 1.927,0.958 0.351,0.181 10 L149 0.174,0.128 0.372,0.297 0.198,0.170 10 *a 0.547,2.844 0.825,2.996 0.277,0.152 10 12V 2.717,2.138 3.083,2.290 0.365,0.152 10 GND 1.206,2.545 0.82,2.809 false 2.671,2.226 2.25,2.455 false

Disconnect the L149 combination meter mirror ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L149-1 (12V) - Body ground Power switch on (IG) 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below

Standard Resistance:
Tester Connection Condition Specified Condition
L149-8 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter Mirror ECU)



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - HEADUP DISPLAY SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER MIRROR ECU - HEADUP DISPLAY SWITCH ASSEMBLY)
a.

Disconnect the L147 headup display switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
L149-14 (HUDU) - L147-3 (NVM) Always Below 1 Ω
L149-14 (HUDU) - Body ground Always 10 kΩ or higher
L149-15 (HUDO) - L147-4 (CH) Always Below 1 Ω
L149-15 (HUDO) - Body ground Always 10 kΩ or higher
L149-16 (E) - L147-1 (E) Always Below 1 Ω
L149-16 (E) - Body ground Always Below 1 Ω




OK

4.INSPECT HEADUP DISPLAY SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEADUP DISPLAY SWITCH ASSEMBLY
a.
E251582E02
0.188,2.346 0.363,2.527 0.174,0.180 10 *a 1.377,3.979 1.713,4.159 0.336,0.180 10 CH 1.878,4.034 2.236,4.214 0.357,0.180 10 NVM 1.898,3.538 2.022,4.013 false 1.704,3.545 1.563,3.97 false 2.428,3.87 2.595,4.051 0.166,0.180 10 E 2.138,3.551 2.417,3.889 false

Disconnect the L147 headup display switch assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (NVM) - 1 (E) SET switch is pressed 1782 to 1818 Ω
SET switch is not pressed 10 kΩ or higher
HUD tilt up switch is pressed 811.8 to 828.2 Ω
HUD tilt up switch is not pressed 10 kΩ or higher
HUD tilt down switch is pressed 326.7 to 333.3 Ω
HUD tilt down switch is not pressed 10 kΩ or higher
4 (CH) - 1 (E) HUD main switch is pressed 1782 to 1818 Ω
HUD main switch is not pressed 10 kΩ or higher
HUD rheostat up switch is pressed 811.8 to 828.2 Ω
HUD rheostat up switch is not pressed 10 kΩ or higher
HUD rheostat down switch is pressed 326.7 to 333.3 Ω
HUD rheostat down switch is not pressed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Headup Display Switch Assembly)



OK

REPLACE COMBINATION METER MIRROR ECU

NG

REPLACE HEADUP DISPLAY SWITCH ASSEMBLY

5.SYSTEM CHECK
a.

Check the symptom of the headup display.

Result:
Result Proceed to
All display items are abnormal. A
Vehicle speed display is abnormal.
Dynamic radar cruise control display is abnormal.
Pre-crash safety system display is abnormal.
Touch tracer display is abnormal.
Turn-by-turn navigation display is abnormal. B




A

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - COMBINATION METER MIRROR ECU)

B

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - COMBINATION METER MIRROR ECU)
6.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - COMBINATION METER MIRROR ECU)
a.

Disconnect the L141 combination meter sub-assembly connector.


b.

Disconnect the L149 combination meter mirror ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
L141-7 (TX+) - L149-3 (SIH) Always Below 1 Ω
L141-7 (TX+) - Body ground Always 10 kΩ or higher
L141-8 (TX-) - L149-4 (SIL) Always Below 1 Ω
L141-8 (TX-) - Body ground Always 10 kΩ or higher
L141-9 (SIH) - L149-5 (TX+) Always Below 1 Ω
L141-9 (SIH) - Body ground Always 10 kΩ or higher
L141-10 (SIL) - L149-6 (TX-) Always Below 1 Ω
L141-10 (SIL) - Body ground Always 10 kΩ or higher




OK

7.REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE COMBINATION METER MIRROR ECU
a.

Replace the combination meter mirror ECU with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY>DISASSEMBLY).

OK:

The operation of the headup display returns to normal.




OK

END

NG

8.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - COMBINATION METER MIRROR ECU)
a.

Disconnect the L141 combination meter sub-assembly connector.


b.

Disconnect the L149 combination meter mirror ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance :
Tester Connection Condition Specified Condition
L141-7 (TX+) - L149-3 (SIH) Always Below 1 Ω
L141-7 (TX+) - Body ground Always 10 kΩ or higher
L141-8 (TX-) - L149-4 (SIL) Always Below 1 Ω
L141-8 (TX-) - Body ground Always 10 kΩ or higher
L141-9 (SIH) - L149-5 (TX+) Always Below 1 Ω
L141-9 (SIH) - Body ground Always 10 kΩ or higher
L141-10 (SIL) - L149-6 (TX-) Always Below 1 Ω
L141-10 (SIL) - Body ground Always 10 kΩ or higher




OK

9.REPLACE COMBINATION METER MIRROR ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE COMBINATION METER MIRROR ECU
a.

Replace the combination meter mirror ECU with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>HEADUP DISPLAY>DISASSEMBLY).

OK:

The operation of the headup display returns to normal.




OK

END

NG

10.REPLACE METER CIRCUIT PLATE
10.REPLACE METER CIRCUIT PLATE
a.

Replace the meter circuit plate with a new or a known good one (See page Vehicle Interior>METER / GAUGE / DISPLAY>COMBINATION METER>DISASSEMBLY).

OK:

The operation of the headup display returns to normal.




OK

END

NG