Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061940 METER / GAUGE / DISPLAY _0301792 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1504  Lost Communication with Steering SW  


DESCRIPTION

The combination meter sub-assembly communicates with the steering pad switch RH via a direct line. If the combination meter assembly detects a communication malfunction, it stores this DTC.

DTC No. DTC Detection Condition Trouble Area
B1504 When the IG voltage is 9.5 V or more and power switch on (IG) and the following condition is detected:
1.

Steering pad switch RH communication error has been detected for more than 3 seconds.


·

Wire harness or connector

·

Spiral cable with sensor sub-assembly

·

Steering pad switch RH

·

Combination meter sub-assembly (Meter circuit plate)



WIRING DIAGRAM

E238317E03
2.292,0.479 3.146,0.677 0.854,0.198 10 false to IG2 Relay 3.51,0.604 3.813,0.802 0.302,0.198 10 false IGN 2.917,1.74 3.125,1.938 0.208,0.198 10 false z9 2.917,2.406 3.125,2.604 0.208,0.198 10 false z9 0.563,2.813 1.854,3.208 1.292,0.396 10 false Steering Pad Switch RH 2.875,2.813 4.563,3.167 1.688,0.354 10 false Spiral Cable with Sensor Sub-assembly 2.958,2.208 3.073,2.385 0.115,0.177 10 false 7 2.958,1.552 3.104,1.729 0.146,0.177 10 false 2 4.219,1.74 4.49,1.938 0.271,0.198 10 false L52 3.948,1.656 4.219,1.854 0.271,0.198 10 false IG 3.854,2.323 4.125,2.521 0.271,0.198 10 false TX1 5.448,2.292 5.719,2.49 0.271,0.198 10 false 10 4.219,2.406 4.49,2.604 0.271,0.198 10 false L52 5,2.656 5.271,2.854 0.271,0.198 10 false L27 5,2.813 7.135,3.177 2.135,0.365 10 false Combination Meter Sub-assembly (Meter Circuit Plate) 5.688,2.396 6.167,2.594 0.479,0.198 10 false STRG 4.281,2.208 4.396,2.385 0.115,0.177 10 false 3 4.281,1.542 4.427,1.719 0.146,0.177 10 false 9

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses of circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS (MULTI DISPLAY SELECT SWITCH, DRIVE MONITOR RESET SW)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Check the values by referring to the table below.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Multi Display Select Switch DISP switch (Steering pad switch assembly) / OFF or ON OFF: DISP switch not pressed -
ON: DISP switch pressed
Drive Monitor Reset SW TRIP switch (Steering pad switch assembly) / OFF or ON OFF: TRIP switch not pressed -
ON: TRIP switch pressed

OK:

Steering pad switch RH condition displayed on the GTS changes with the actual switch operation.




OK

NG

2.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
2.INSPECT SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.

Disconnect the L52 and z9 spiral cable with sensor sub-assembly connectors.

C370355E03
4.354,0.094 4.771,0.344 0.417,0.25 4.229,1.594 4.646,1.844 0.417,0.25 0.24,0.115 0.552,0.313 0.313,0.198 10 false *a 4.49,0.135 4.802,0.333 0.313,0.198 10 false z9 4.313,1.635 4.625,1.833 0.313,0.198 10 false L52


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L52-3 (TX1) - z9-7 Always Below 1 Ω
L52-9 (IG) - z9-2 Always Below 1 Ω


Text in Illustration
*a Component without harness connected
(Spiral Cable with Sensor Sub-assembly)



OK

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - IG2 RELAY)

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY - IG2 RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L52-9 (IG) - Body ground Power switch off Below 1 V
L52-9 (IG) - Body ground Power switch on (IG) 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - STEERING PAD SWITCH RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - STEERING PAD SWITCH RH)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L27-10 (STRG) - L52-3 (TX1) Always Below 1 Ω
L27-10 (STRG) - Body ground Always 10 kΩ or higher




OK

5.REPLACE STEERING PAD SWITCH RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE STEERING PAD SWITCH RH
a.

Replace the steering pad switch RH with a new or a known good one (See page Steering>STEERING COLUMN>STEERING PAD SWITCH>REMOVAL).

OK:

The operation of the combination meter sub-assembly returns to normal.




OK

END

NG