Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DTC CHECK / CLEAR  


DTC CHECK (USING SST CHECK WIRE)


a.
C204945E07
2.03,1.775 2.257,1.912 0.227,0.137 10 TC 1.805,1.339 1.805,1.861 1.805,1.861 1.991,1.861 false 1.638,0.791 1.638,0.269 1.638,0.269 1.825,0.269 false 1.867,0.181 2.094,0.318 0.227,0.137 10 CG

Check for DTCs (Current trouble codes).

i.

Turn the power switch on (IG), and wait for approximately 60 seconds.


ii.

Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  

NOTICE:

Connect the terminals to the correct positions to avoid a malfunction.




b.

Check for DTCs (History trouble codes).

i.

Using SST, connect terminals TC and CG of the DLC3.

SST
09843-18040  

NOTICE:

Connect the terminals to the correct positions to avoid a malfunction.



ii.

Turn the power switch on (IG), and wait for approximately 60 seconds.



c.

Read the DTCs.

C327548E01
0.073,0.083 6.844,0.302 6.771,0.219 10 false Normal System Code (without History Trouble Code): 1.406,0.542 2.156,0.75 0.75,0.208 10 false 0.25 sec. 0.854,0.823 1.604,1.031 0.75,0.208 10 false ON 0.813,1.167 1.563,1.375 0.75,0.208 10 false OFF 0.823,2.635 1.573,2.844 0.75,0.208 10 false ON 0.771,3.01 1.521,3.219 0.75,0.208 10 false OFF 4.042,0.906 4.792,1.115 0.75,0.208 10 false ON 4,1.167 4.75,1.375 0.75,0.208 10 false OFF 1.635,1.313 2.385,1.521 0.75,0.208 10 false 0.25 sec. 0.104,1.906 6.875,2.125 6.771,0.219 10 false Normal System Code (with History Trouble Code): 1.667,2.396 2.417,2.604 0.75,0.208 10 false 0.75 sec. 1.844,3.104 2.594,3.313 0.75,0.208 10 false 0.25 sec. 3.833,0.094 6.74,0.344 2.906,0.25 10 false Trouble Code (Example Codes 11 and 31): 4.073,0.469 4.823,0.677 0.75,0.208 10 false 0.5 sec. 4.625,0.458 5.375,0.667 0.75,0.208 10 false 2.5 sec. 5.469,0.458 6.219,0.667 0.75,0.208 10 false 4.0 sec. 5.958,1.479 6.708,1.688 0.75,0.208 10 false Repeat 4.896,1.458 5.646,1.667 0.75,0.208 10 false 0.5 sec. 4.333,1.469 5.083,1.677 0.75,0.208 10 false 1.5 sec. 4.354,1.885 5.104,2.094 0.75,0.208 10 false DTC 11 5.01,1.875 5.76,2.083 0.75,0.208 10 false DTC 31

i.

Read the blinking patterns of the DTCs. As an examples, the blinking patterns for the normal system code and trouble codes 11 and 31 are shown in the illustration.

·

Normal system code indication (without history trouble code)

The light blinks twice per second.

·

Normal system code indication (with history trouble code)

When a history trouble code is stored in the airbag ECU assembly, the light blinks only once per second.

·

Trouble code indication

The first blink(s) indicate the first number of the DTC. The second blink(s) indicate the second number of the DTC and occur after a 1.5-second pause.


NOTICE:

When a DTC includes a letter (such as DTC 8A), the light blinks 8 times and then it blinks 10 times to indicate the A after a 1.5-second pause.

Comparison Table
Number of Blinks Indicated Letter
10 A
11 B
12 C
13 D
14 E
15 F


If there is more than 1 code, there will be a 2.5-second pause between each code. After all codes are shown, there will be a 4.0-second pause, and then all codes will be repeated.

HINT:
·

If 2 or more malfunctions are found, the indication begins with the smaller-numbered code.

·

If DTCs are indicated without connecting the terminals, proceed to TC and CG Terminal Circuit (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>TC and CG Terminal Circuit).






DTC CLEAR (USING SST CHECK WIRE)


a.

Clear the DTCs.

i.

When the power switch is turned off, the DTCs are cleared.

HINT:

Depending on the DTC, the code may not be cleared by turning off the power switch. In this case, proceed to the next procedure.



ii.

Using SST, connect terminals TC and CG of the DLC3, and then turn the power switch on (IG).

SST
09843-18040  


iii.

Disconnect terminal TC of the DLC3 within 3 to 10 seconds after the DTCs are output, and check if the SRS warning light comes on after 3 seconds.


iv.

Within 2 to 4 seconds after the SRS warning light comes on, connect terminals TC and CG of the DLC3.


v.

The SRS warning light should go off within 2 to 4 seconds after connecting terminals TC and CG of the DLC3. Then, disconnect terminal TC within 2 to 4 seconds after the SRS warning light goes off.


vi.

The SRS warning light comes on again within 2 to 4 seconds after disconnecting terminal TC. Then, reconnect terminals TC and CG within 2 to 4 seconds after the SRS warning light comes on.


vii.

Check if the SRS warning light goes off within 2 to 4 seconds after connecting terminals TC and CG of the DLC3. Also check if the normal system code is output within 1 second after the SRS warning light goes off.

If DTCs are not cleared, repeat this procedure until the codes are cleared.

C123780E98
0.083,0.552 0.979,0.719 0.896,0.167 10 false Power Switch 0.083,1.292 1.323,1.479 1.24,0.188 10 false DLC3 (TC and CG) 0.083,2.125 1.49,2.333 1.406,0.208 10 false SRS Warning Light* 3.073,1.698 3.594,1.906 0.521,0.208 10 false 0.5 sec. 5.573,1.698 6.156,1.906 0.583,0.208 10 true 0.25 sec. 0.365,2.521 1.396,2.698 1.031,0.177 10 false T1: 0 to ∞ sec. 0.365,2.833 1.521,3.042 1.156,0.208 10 false T2: approx. 6 sec. 0.365,3.135 1.302,3.333 0.938,0.198 10 false T3: 3 to 5 sec. 0.365,3.469 1.354,3.677 0.99,0.208 10 false T4: 3 to 10 sec. 0.365,3.76 1.302,3.938 0.938,0.177 10 false T5: 2 to 4 sec. 0.365,4.094 1.292,4.271 0.927,0.177 10 false T6: 1 to 5 sec. 0.365,4.438 1.417,4.625 1.052,0.188 10 false T7: within 1 sec. 2.229,4.292 6.927,4.531 4.698,0.24 10 false *: The history trouble code in the illustration shows DTC 21 as an example. 2.458,3.458 2.656,3.688 0.198,0.229 10 false T1 5.948,3.458 6.177,3.688 0.229,0.229 10 false T7 4.417,3.458 4.615,3.688 0.198,0.229 10 false T6 4.167,3.458 4.354,3.688 0.188,0.229 10 false T5 3.729,3.458 3.948,3.688 0.219,0.229 10 false T4 3.24,3.458 3.458,3.688 0.219,0.229 10 false T3 2.844,3.458 3.083,3.688 0.24,0.229 10 false T2 4.938,3.458 5.125,3.688 0.188,0.229 10 false T6 4.688,3.458 4.875,3.688 0.188,0.229 10 false T5 5.448,3.458 5.635,3.688 0.188,0.229 10 false T6 5.198,3.458 5.385,3.688 0.188,0.229 10 false T5 5.708,3.458 5.938,3.688 0.229,0.229 10 false T5 6.198,1.698 6.802,1.906 0.604,0.208 10 true 0.25 sec. 3.635,1.698 4.146,1.906 0.51,0.208 10 true 0.5 sec. 1.792,0.396 2.271,0.594 0.479,0.198 10 false On (IG) 1.802,0.823 2.135,1.021 0.333,0.198 10 false OFF 1.417,1.552 2.135,1.74 0.719,0.188 10 false Connected 1.75,1.156 2.167,1.333 0.417,0.177 10 false Open 1.875,2.135 2.135,2.302 0.26,0.167 10 false ON 1.813,2.5 2.135,2.677 0.323,0.177 10 false OFF 3.594,2.865 4.115,3.073 0.521,0.208 10 false 1.5 sec.




DTC CHECK (USING GTS)


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG), and wait for approximately 60 seconds.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


f.

Check for DTCs by following the prompts on the GTS screen.

HINT:

Refer to the GTS operator's manual for further details.




DTC CLEAR (USING GTS)


a.

Turn the power switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the power switch on (IG), and wait for approximately 60 seconds.


d.

Turn the GTS on.


e.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


f.

Clear the DTCs by following the prompts on the GTS screen.

HINT:

Refer to the GTS operator's manual for further details.