Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2013.08–2014.11
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800/51  Short in Driver Side Squib Circuit  B1801/51  Open in Driver Side Squib Circuit  B1802/51  Short to GND in Driver Side Squib Circuit  B1803/51  Short to B+ in Driver Side Squib Circuit  


DESCRIPTION

The driver side squib circuit consists of the airbag ECU assembly, spiral cable with sensor sub-assembly and horn button assembly.

The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.


DTC No. DTC Detection Condition Trouble Area
B1800/51
·

The airbag ECU assembly receives a line short circuit signal in the driver side squib circuit during primary check.

·

Spiral cable with sensor sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


·

Instrument panel wire

·

Spiral cable with sensor sub-assembly

·

Horn button assembly (Driver side squib)

·

Airbag ECU assembly


B1801/51
·

The airbag ECU assembly receives an open circuit signal in the driver side squib circuit.

·

Spiral cable with sensor sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


B1802/51
·

The airbag ECU assembly receives a short circuit to ground signal in the driver side squib circuit.

·

Spiral cable with sensor sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction


B1803/51
·

The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib circuit.

·

Spiral cable with sensor sub-assembly malfunction

·

Driver side squib malfunction

·

Airbag ECU assembly malfunction



WIRING DIAGRAM

C239226E08
4.684,3.029 5.048,3.181 0.364,0.151 10 L16 4.684,3.204 6.414,3.356 1.730,0.151 10 Airbag ECU Assembly 2.709,2.526 3.027,2.677 0.318,0.151 10 L53 3.24,1.071 3.516,1.223 0.276,0.151 10 D+ 3.24,1.903 3.491,2.054 0.251,0.151 10 D- 4.719,1.16 5.009,1.311 0.290,0.151 10 D+ 4.719,2.004 4.965,2.155 0.246,0.151 10 D- 2.406,1.071 2.505,1.223 0.099,0.151 10 2 2.406,1.903 2.505,2.054 0.099,0.151 10 1 4.528,1.903 4.627,2.054 0.099,0.151 10 6 4.528,1.071 4.627,1.223 0.099,0.151 10 5 2.709,2.701 4.110,3.048 1.401,0.346 10 Spiral Cable with Sensor Sub-assembly 0.708,2.701 2.164,3.092 1.457,0.391 10 Horn Button Assembly (Driver Side Squib) 0.708,2.526 0.988,2.677 0.281,0.151 10 z8 3.521,1.903 3.620,2.054 0.099,0.151 10 2 3.521,1.071 3.620,1.223 0.099,0.151 10 1 2.137,1.071 2.427,1.223 0.290,0.151 10 D+ 2.137,1.903 2.383,2.054 0.246,0.151 10 D-

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:
·

Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).

·

After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).



PROCEDURE

1.CHECK CONNECTORS
a.
C241740E07
0.205,1.342 0.361,1.494 0.156,0.152 10 *1 1.03,0.798 1.197,0.963 0.167,0.165 10 *2 2.698,1.106 2.873,1.262 0.174,0.156 10 *3 1.902,1.342 2.055,1.494 0.153,0.151 10 *4 2.368,0.798 2.484,0.951 0.117,0.153 10 A 2.102,0.798 2.219,0.951 0.117,0.153 10 B 1.754,0.798 1.881,0.951 0.127,0.153 10 C 1.492,0.798 1.619,0.951 0.127,0.153 10 D 0.641,0.798 0.768,0.951 0.127,0.153 10 E 0.389,0.798 0.516,0.951 0.127,0.153 10 F 1.988,0.947 1.988,1.336 false 0.287,0.947 0.287,1.336 false

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the horn button assembly, spiral cable with sensor sub-assembly and airbag ECU assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.



d.

Disconnect the connectors from the horn button assembly, spiral cable with sensor sub-assembly and airbag ECU assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the spiral cable with sensor sub-assembly connector (on the horn button assembly side) is not damaged.

OK:

The lock button is not disengaged, or the claw of the lock is not deformed or damaged.



g.

Check that the short springs for the instrument panel wire and spiral cable with sensor sub-assembly with the activation prevention mechanism are not deformed or damaged.

OK:

The short springs are not deformed or damaged.


Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable with Sensor Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire



OK

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)

NG

REPLACE WIRE HARNESS

2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB)
a.
U191115E02
1.76,2.229 1.948,2.229 false 0.323,0.677 0.323,0.958 false 0.49,2.313 0.688,2.458 0.198,0.146 10 false z8 0.438,0.531 0.542,0.688 0.104,0.156 10 false F 0.76,0.531 0.885,0.688 0.125,0.156 10 false E 1.604,0.531 1.729,0.688 0.125,0.156 10 false D 1.76,0.531 1.885,0.688 0.125,0.156 10 false C 2.188,0.531 2.313,0.688 0.125,0.156 10 false B 2.344,0.531 2.469,0.688 0.125,0.156 10 false A 1.156,0.51 1.333,0.688 0.177,0.177 10 false *2 0.24,0.969 0.396,1.146 0.156,0.177 10 false *1 2.698,0.781 2.875,0.927 0.177,0.146 10 false *3 0.333,1.688 0.51,1.854 0.177,0.167 10 false *a 1.99,2.156 2.281,2.313 0.292,0.156 10 false SST

Connect the instrument panel wire to the airbag ECU assembly and spiral cable with sensor sub-assembly.


b.

Connect SST (resistance 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the horn button assembly (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting it.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

c.

Connect the cable to the negative (-) auxiliary battery terminal.



e.

Turn the power switch off.


f.

Turn the power switch on (IG), and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.



h.

Turn the power switch off.


i.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



j.

Disconnect SST from connector E.

Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable with Sensor Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)



OK

NG

3.CHECK DRIVER SIDE SQUIB CIRCUIT
3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.
U191084E02
0.323,0.698 0.323,0.99 false 1.271,2.063 0.979,2.063 true 1.781,2.052 1.49,2.052 true 0.542,2.271 0.74,2.417 0.198,0.146 10 false z8 0.448,0.531 0.552,0.688 0.104,0.156 10 false F 0.76,0.531 0.885,0.688 0.125,0.156 10 false E 1.604,0.531 1.729,0.688 0.125,0.156 10 false D 1.76,0.531 1.885,0.688 0.125,0.156 10 false C 2.208,0.531 2.333,0.688 0.125,0.156 10 false B 2.521,0.542 2.646,0.698 0.125,0.156 10 false A 1.146,0.521 1.323,0.698 0.177,0.177 10 false *2 0.24,0.99 0.396,1.167 0.156,0.177 10 false *1 2.813,0.813 2.99,0.958 0.177,0.146 10 false *3 0.24,1.615 0.417,1.781 0.177,0.167 10 false *a 0.792,1.979 0.969,2.125 0.177,0.146 10 false D- 1.813,1.99 2.031,2.135 0.219,0.146 10 false D+

Disconnect the instrument panel wire from the airbag ECU assembly.


b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z8-2 (D+) - Body ground Power switch on (IG) Below 1 V
z8-1 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D+) - z8-1 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D+) - Body ground Always 1 MΩ or higher
z8-1 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D+) - z8-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable with Sensor Sub-assembly
*3 Airbag ECU Assembly
*a Front view of wire harness connector
(to Horn Button Assembly)




OK

4.CHECK DTC

NG

5.CHECK INSTRUMENT PANEL WIRE
4.CHECK DTC
a.
C238229E01
0.366,1.282 0.522,1.433 0.156,0.152 10 *1 1.083,0.731 1.251,0.896 0.167,0.165 10 *2 2.618,1.008 2.792,1.164 0.174,0.156 10 *3 2.305,0.731 2.421,0.884 0.117,0.153 10 A 2.145,0.731 2.261,0.884 0.117,0.153 10 B 1.694,0.731 1.821,0.884 0.127,0.153 10 C 1.531,0.731 1.658,0.884 0.127,0.153 10 D 0.704,0.731 0.831,0.884 0.127,0.153 10 E 0.55,0.731 0.677,0.884 0.127,0.153 10 F 0.449,0.88 0.449,1.269 false

Connect the connectors to the horn button assembly and airbag ECU assembly.


b.

Connect the cable to the negative (-) auxiliary battery terminal.



d.

Turn the power switch off.


e.

Turn the power switch on (IG), and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800/51, B1801/51, B1802/51 or B1803/51 is not output.


HINT:

Codes other than DTCs B1800/51, B1801/51, B1802/51 and B1803/51 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable with Sensor Sub-assembly
*3 Airbag ECU Assembly



OK

NG

5.CHECK INSTRUMENT PANEL WIRE
a.

Disconnect the instrument panel wire from the spiral cable with sensor sub-assembly.


U191083E01
1.226,2.347 1.502,2.491 0.275,0.144 10 L53 0.332,0.532 0.442,0.685 0.109,0.153 10 F 0.655,0.532 0.776,0.685 0.121,0.153 10 E 1.491,0.532 1.612,0.685 0.121,0.153 10 D 1.81,0.532 1.931,0.685 0.121,0.153 10 C 2.26,0.532 2.380,0.685 0.121,0.153 10 B 2.572,0.532 2.692,0.685 0.121,0.153 10 A 1.049,0.532 1.226,0.708 0.177,0.175 10 *2 0.135,0.974 0.287,1.149 0.152,0.175 10 *1 2.882,0.816 3.058,0.960 0.176,0.144 10 *3 1.032,1.606 1.206,1.771 0.174,0.165 10 *a 2.382,2.886 2.558,3.034 0.177,0.148 10 D- 1.737,0.117 1.892,0.268 0.155,0.151 10 *4 0.22,0.68 0.22,0.965 false 1.669,2.886 1.878,3.037 0.209,0.151 10 D+ 2.03,2.504 1.8,2.855 false 2.233,2.504 2.463,2.855 false 2.087,0.536 2.087,0.204 2.087,0.204 1.921,0.204 false

b.

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L53-1 (D+) - Body ground Power switch on (IG) Below 1 V
L53-2 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




c.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L53-1 (D+) - L53-2 (D-) Always Below 1 Ω




d.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L53-1 (D+) - Body ground Always 1 MΩ or higher
L53-2 (D-) - Body ground Always 1 MΩ or higher




e.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L53-1 (D+) - L53-2 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable with Sensor Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Spiral Cable with Sensor Sub-assembly)




OK

6.CHECK SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY
a.
U191082E02
0.229,0.688 0.229,0.979 false 2.094,0.688 2.094,0.979 false 1.281,2.052 0.99,2.052 true 1.781,2.063 1.49,2.063 true 0.521,2.281 0.719,2.427 0.198,0.146 10 false z8 0.344,0.531 0.448,0.688 0.104,0.156 10 false F 0.656,0.531 0.781,0.688 0.125,0.156 10 false E 1.5,0.531 1.625,0.688 0.125,0.156 10 false D 1.813,0.531 1.938,0.688 0.125,0.156 10 false C 2.26,0.531 2.385,0.688 0.125,0.156 10 false B 2.573,0.521 2.698,0.677 0.125,0.156 10 false A 1.031,0.531 1.208,0.708 0.177,0.177 10 false *2 0.146,0.979 0.302,1.156 0.156,0.177 10 false *1 2.875,0.813 3.052,0.958 0.177,0.146 10 false *3 0.229,1.594 0.406,1.76 0.177,0.167 10 false *a 0.802,1.958 0.979,2.104 0.177,0.146 10 false D- 2.01,0.969 2.167,1.146 0.156,0.177 10 false *4 1.813,1.99 2.031,2.135 0.219,0.146 10 false D+

Check for a short to B+ in the circuit.

i.

Connect the cable to the negative (-) auxiliary battery terminal.


ii.

Turn the power switch on (IG).


iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
z8-2 (D+) - Body ground Power switch on (IG) Below 1 V
z8-1 (D-) - Body ground Power switch on (IG) Below 1 V



iv.

Turn the power switch off.


v.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.




b.

Check for an open in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D+) - z8-1 (D-) Always Below 1 Ω




c.

Check for a short to ground in the circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D+) - Body ground Always 1 MΩ or higher
z8-1 (D-) - Body ground Always 1 MΩ or higher




d.

Check for a short in the circuit.

i.

Release the activation prevention mechanism built into connector D (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z8-2 (D+) - z8-1 (D-) Always 1 MΩ or higher



iii.

Restore the released activation prevention mechanism of connector D to the original condition.

Text in Illustration
*1 Horn Button Assembly
*2 Spiral Cable with Sensor Sub-assembly
*3 Airbag ECU Assembly
*4 Instrument Panel Wire
*a Front view of wire harness connector
(to Horn Button Assembly)




OK

NG

REPLACE SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY