Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1635/24  Rear Airbag Sensor LH Circuit Malfunction  


DESCRIPTION

The side collision sensor LH circuit (to determine deployment of the front seat airbag assembly LH, curtain shield airbag assembly LH and front seat outer belt assembly LH) is composed of the airbag ECU assembly, side airbag sensor assembly LH and side No. 2 airbag sensor assembly LH.

The side No. 2 airbag sensor assembly LH detects impacts to the vehicle and sends signals to the airbag ECU assembly to determine if the airbag should be deployed.

DTC B1635/24 is stored when a malfunction is detected in the side No. 2 airbag sensor assembly LH.

DTC No. DTC Detection Condition Trouble Area
B1635/24
·

Side No. 2 airbag sensor assembly LH malfunction

·

Airbag ECU assembly malfunction


·

Side No. 2 airbag sensor assembly LH

·

Airbag ECU assembly



WIRING DIAGRAM

Refer to DTCs B1627/82, B1628/82, B1637/82, B1638/82 and B1647/82 (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>B1627/82).

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.CHECK SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH
a.
C238223E01
0.969,0.972 1.119,1.124 0.150,0.152 10 *1 2.271,0.972 2.420,1.124 0.150,0.152 10 *2 2.036,0.972 2.163,1.137 0.128,0.166 10 A 1.883,0.972 2.011,1.137 0.128,0.166 10 B 1.425,0.972 1.552,1.137 0.128,0.166 10 C 1.268,0.972 1.396,1.137 0.128,0.166 10 D

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Interchange the side No. 2 airbag sensor assembly LH with RH and connect the connectors to them.


d.

Connect the cable to the negative (-) auxiliary battery terminal.



f.

Turn the power switch off.


g.

Turn the power switch on (IG), and wait for at least 60 seconds.


h.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1635/24 is output. A
DTC B1630/23 is output. B
DTCs B1630/23 and B1635/24 are not output. C


HINT:

Codes other than DTCs B1630/23 and B1635/24 may be output at this time, but they are not related to this check.



i.

Turn the power switch off.


j.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



k.

Return the side No. 2 airbag sensor assembly LH and RH to their original positions and connect the connectors.

Text in Illustration
*1 Side No. 2 Airbag Sensor Assembly RH
*2 Side Airbag Sensor Assembly LH



A

B

REPLACE SIDE NO. 2 AIRBAG SENSOR ASSEMBLY LH

C