Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301798 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  Trouble in Passenger Airbag ON/OFF Indicator  


DESCRIPTION

This circuit detects the airbag cut off switch cylinder sub-assembly status.

The passenger airbag ON/OFF indicator comes on to inform the front passenger airbag status (activated or deactivated).

HINT:

Approximately 6 seconds after the power switch is turned on (IG), the passenger airbag ON/OFF indicator will indicate ON/OFF depending on the conditions listed below.

Airbag Cut Off Switch Cylinder Sub-assembly Passenger Airbag ON/OFF Indicator SRS Warning Light
ON Indicator OFF Indicator
ON position ON OFF OFF
OFF position OFF ON OFF
Switch failure OFF ON ON


WIRING DIAGRAM

C261689E02
0.573,3.51 0.948,3.667 0.375,0.156 10 false L148 0.573,3.667 2.448,4.063 1.875,0.396 10 false Airbag Cut Off Switch Cylinder Sub-assembly 5.604,3.708 5.885,3.865 0.281,0.156 10 false L16 5.604,3.865 7.031,4.052 1.427,0.188 10 false Airbag ECU Assembly 5.615,1.313 6.063,1.458 0.448,0.146 10 false MSW+ 5.333,1.188 5.51,1.344 0.177,0.156 10 false 11 5.615,2.813 6.031,2.958 0.417,0.146 10 false MSW- 2.365,1.188 2.781,1.333 0.417,0.146 10 false PMC+ 2.375,2.677 2.76,2.823 0.385,0.146 10 false PMC- 5.333,2.688 5.51,2.844 0.177,0.156 10 false 12 2.906,1.188 3,1.344 0.094,0.156 10 false 2 2.906,2.688 3,2.844 0.094,0.156 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

Terminals L16-11 (MSW+) and L16-12 (MSW-) of the airbag ECU assembly in this circuit have an activation prevention mechanism.

This mechanism can be used to check for an open circuit in the wire harness. In case of other checks (check for short, short to ground or short to B+), this mechanism should be released.


PROCEDURE

1.CHECK SRS WARNING LIGHT
a.

Turn the power switch on (IG), and check the SRS warning light condition.

HINT:

If this trouble occurs, the SRS warning light is off. If it is on, a DTC is stored. Troubleshoot for the stored DTC.


OK:

After the primary check period, the SRS warning light goes off.


HINT:

The primary check period is approximately 6 seconds after the power switch is turned on (IG).




OK

2.CHECK CONNECTORS

NG

2.CHECK CONNECTORS
a.

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Check that the connectors are properly connected to the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.

OK:

The connectors are properly connected.


HINT:

If the connectors are not connected securely, reconnect the connector and proceed to the next inspection.



d.

Disconnect the connectors from the airbag ECU assembly and airbag cut off switch cylinder sub-assembly.


e.

Check that the terminals of the connectors are not damaged.

OK:

The terminals are not deformed or damaged.



f.

Check that the short spring for the instrument panel wire connector with the activation prevention mechanism is not deformed or damaged.

OK:

The short spring is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (OPEN)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (OPEN)
a.
U191144E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.067,2.303 1.427,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - L148-1 (PMC-) Always Below 1 Ω


Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

4.CHECK INSTRUMENT PANEL WIRE (SHORT)

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK INSTRUMENT PANEL WIRE (SHORT)
a.
U191144E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.067,2.303 1.427,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - L148-1 (PMC-) Always 1 MΩ or higher



c.

Restore the released activation prevention mechanism of connector B to the original condition.

Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)

NG

REPLACE INSTRUMENT PANEL WIRE

5.CHECK INSTRUMENT PANEL WIRE (SHORT TO B+)
a.
U191144E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.067,2.303 1.427,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Connect the cable to the negative (-) auxiliary battery terminal.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - Body ground Power switch on (IG) Below 1 V
L148-1 (PMC-) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)

NG

REPLACE INSTRUMENT PANEL WIRE

6.CHECK INSTRUMENT PANEL WIRE (SHORT TO GROUND)
a.
U191144E01
1.29,0.533 1.422,0.689 0.132,0.157 10 C 0.885,0.533 1.017,0.689 0.132,0.157 10 D 1.754,0.533 1.885,0.689 0.132,0.157 10 B 2.166,0.533 2.298,0.689 0.132,0.157 10 A 0.567,0.528 0.750,0.720 0.183,0.192 10 *1 1.067,2.303 1.427,2.460 0.359,0.158 10 L148 2.26,2.901 2.678,3.058 0.417,0.158 10 PMC+ 1.618,2.898 2.015,3.056 0.397,0.158 10 PMC- 1.588,0.551 1.588,0.233 1.588,0.233 1.692,0.233 false 2.583,0.809 2.766,1.001 0.183,0.192 10 *2 1.727,0.161 1.910,0.353 0.183,0.192 10 *3 0.782,1.624 0.965,1.817 0.183,0.192 10 *a 2.283,2.63 2.46,2.91 false 1.854,2.901 2.03,2.622 false

Turn the power switch off.


b.

Disconnect the cable from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - Body ground Always 1 MΩ or higher
L148-1 (PMC-) - Body ground Always 1 MΩ or higher


Text in Illustration
*1 Airbag Cut Off Switch Cylinder Sub-assembly
*2 Airbag ECU Assembly
*3 Instrument Panel Wire
*a Front view of wire harness connector
(to Airbag Cut Off Switch Cylinder Sub-assembly)



OK

7.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE

7.CHECK AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY
a.
U191145E01
0.225,0.162 0.422,0.385 0.198,0.223 10 *a 2.75,0.743 3.162,0.899 0.412,0.157 10 PMC+ 2.75,1.198 3.137,1.355 0.387,0.157 10 PMC- 2.331,1.039 2.737,0.834 false 2.332,1.125 2.739,1.282 false 2.773,0.421 3.123,0.584 0.350,0.163 10 L148

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L148-2 (PMC+) - L148-1 (PMC-) Cut off switch is ON 360 to 440 Ω
L148-2 (PMC+) - L148-1 (PMC-) Cut off switch is OFF 90 to 110 Ω


Text in Illustration
*a Component without harness connected
(Airbag Cut Off Switch Cylinder Sub-assembly)



OK

NG

REPLACE AIRBAG CUT OFF SWITCH CYLINDER SUB-ASSEMBLY