The passenger airbag ON/OFF indicator circuit consists of the airbag ECU assembly and air conditioning control assembly (passenger airbag ON/OFF indicator).
The passenger airbag ON/OFF indicator indicates the operation condition of the front passenger airbag.
DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1660/43 | ·
The airbag ECU assembly receives a line short circuit signal, an open circuit signal, a short circuit to ground signal or a short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit. ·
Air conditioning control assembly malfunction ·
Airbag ECU assembly malfunction |
·
Instrument panel wire ·
Air conditioning control assembly (Passenger airbag ON/OFF indicator) ·
Airbag ECU assembly |
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Perform the simulation method by selecting check mode (Signal Check) using the GTS (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE).
After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING).
Turn the power switch on (IG).
Check the passenger airbag ON/OFF indicator operation.
| ON/OFF Indicator Illumination | Proceed to |
|---|---|
| Always ON | A |
| OFF | B |
Refer to the normal condition of the passenger airbag ON/OFF indicator (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
A
B
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag ECU assembly and air conditioning control assembly.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag ECU assembly and air conditioning control assembly.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Connect the connector to the air conditioning control assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Check the passenger airbag ON/OFF indicator operation.
The passenger airbag ON/OFF indicator does not come on.
OK
NG
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Connect the connector to the airbag ECU assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1660/43 is not output.
Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Disconnect the connector from the air conditioning control assembly.
Using a service wire, connect terminals 23 (PAON) and 17 (P-A/B) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - L20-13 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
| *b | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - L20-13 (P-AB) | Always | 1 MΩ or higher |
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - Body ground | Power switch on (IG) | Below 1 V |
| L20-13 (P-AB) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - Body ground | Always | 1 MΩ or higher |
| L20-13 (P-AB) - Body ground | Always | 1 MΩ or higher |
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
Check that the connectors are properly connected to the airbag ECU assembly and air conditioning control assembly.
The connectors are properly connected.
If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the airbag ECU assembly and air conditioning control assembly.
Check that the terminals of the connectors are not damaged.
The terminals are not deformed or damaged.
OK
NG
Using a service wire, connect terminals 23 (PAON) and 17 (P-A/B) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting the wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - L20-13 (P-AB) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *4 | Service Wire |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
| *b | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - L20-13 (P-AB) | Always | 1 MΩ or higher |
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - Body ground | Power switch on (IG) | Below 1 V |
| L20-13 (P-AB) - Body ground | Power switch on (IG) | Below 1 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-5 (PAON) - Body ground | Always | 1 MΩ or higher |
| L20-13 (P-AB) - Body ground | Always | 1 MΩ or higher |
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L20-16 (IG+) - Body ground | Power switch on (IG) | 11 to 14 V |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Air Conditioning Control Assembly) |
OK
NG
Connect the connector to the air conditioning control assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Check the indicator according to the conditions in the table below.
| Terminal Connection | Condition | Specified Condition |
|---|---|---|
| L16-23 (PAON) - Body ground | Power switch on (IG) | "ON" comes on |
| L16-17 (P-A/B) - Body ground | Power switch on (IG) | "OFF" comes on |
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
| *3 | Instrument Panel Wire |
| *a | Front view of wire harness connector
(to Airbag ECU Assembly) |
OK
NG
Connect the connector to the airbag ECU assembly.
Connect the cable to the negative (-) auxiliary battery terminal.
Clear the DTCs stored in memory (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the power switch off.
Turn the power switch on (IG), and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1660/43 is not output.
Codes other than DTC B1660/43 may be output at this time, but they are not related to this check.
| *1 | Air Conditioning Control Assembly |
| *2 | Airbag ECU Assembly |
OK
(See pageGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING)
NG