Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › KNEE AIRBAG ASSEMBLY › 2013.08–2014.11
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301801 KNEE AIRBAG ASSEMBLY A

SUPPLEMENTAL RESTRAINT SYSTEMS  KNEE AIRBAG ASSEMBLY  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

CAUTION:

Be sure to read Precaution thoroughly before servicing (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION).


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 7.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 58810J 8.REMOVE CONSOLE BOX ASSEMBLY

Hide 55431B 10.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL

Hide 55480D 11.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 12.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY

Hide 55606 13.REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 73900 14.REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

CAUTION:

When storing the lower No. 1 instrument panel airbag assembly, keep the airbag deployment side facing upward.


a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.
B282146E02
1.281,3.583 1.479,3.76 0.198,0.177 10 true *A

Remove the 4 bolts.

Text in Illustration
*A for LHD


d.

for LHD:

i.

Disengage the 2 claws to disconnect the DLC3.



e.
B282147

Disengage the 6 claws and 3 guides to remove the lower No. 1 instrument panel airbag assembly.

NOTICE:

When removing the lower No. 1 instrument panel airbag assembly, do not pull the airbag wire harness.



f.
B282149E02
2.48,2.234 2.633,2.391 0.154,0.157 10 *a 1.998,2.294 2.454,2.294 false 2.078,0.384 2.232,0.542 0.154,0.157 10 *1 2.678,0.717 2.434,0.473 2.434,0.473 2.262,0.473 false 2.475,2.594 2.629,2.751 0.154,0.157 10 *2 2.451,2.674 1.995,2.674 1.995,2.674 1.801,2.48 false

Remove the clamp.


g.

Using a screwdriver with the tip wrapped with protective tape, release the airbag connector lock.

Text in Illustration
*1 Airbag Connector Lock
*2 Airbag Connector
*a Protective Tape


h.

Disconnect the airbag connector to remove the lower No. 1 instrument panel airbag assembly.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.