Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR › 2013.08–2014.11
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301807 SIDE AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89860A 1.INSTALL SIDE AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B442007


d.

Insert the pin (stopper) into the body hole and install the side airbag sensor assembly to the vehicle body with the bolt.

B282169E02
2.115,1.948 1.969,1.792 1.969,1.792 1.823,1.792 true 3.802,2 3.656,1.854 3.656,1.854 3.51,1.854 true 3.927,1.885 3.781,1.74 3.781,1.74 3.646,1.74 true 2.208,1.833 2.052,1.688 2.052,1.688 1.917,1.688 true 3.49,1.656 3.656,1.813 0.167,0.156 10 false *1 3.823,2.427 4,2.604 0.177,0.177 10 false *a 1.604,1.719 1.833,1.906 0.229,0.188 10 false (A) 3.292,1.771 3.521,1.958 0.229,0.188 10 false (A) 1.76,1.604 1.927,1.76 0.167,0.156 10 false *1

Text in Illustration
*1 White Housing Lock - -
*a Slide - -

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the bolt while holding the side airbag sensor assembly because the side airbag sensor assembly pin (stopper) is easily damaged.




e.

Connect the connector to the side airbag sensor assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installation parts of the side airbag sensor assembly.


Hide 62414A 2.INSTALL CENTER PILLAR LOWER GARNISH

Hide 62332A 3.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 62312B 5.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 7.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).