Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › REAR AIRBAG SENSOR › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061942 SUPPLEMENTAL RESTRAINT SYSTEMS _0301808 REAR AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  REAR AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89860B 1.INSTALL SIDE NO. 2 AIRBAG SENSOR ASSEMBLY

a.

Check that the power switch is off.


b.

Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.



c.

Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

B442007


d.

Insert the pin (stopper) into the body hole and install the side No. 2 airbag sensor assembly to the vehicle body with the bolt.

B282171E02
2.104,1.896 1.958,1.75 1.958,1.75 1.823,1.75 true 3.802,2 3.656,1.844 3.656,1.844 3.521,1.844 true 4.031,2.052 4.25,2.052 true 5.677,2.125 5.896,2.125 true 4.271,1.979 4.438,2.135 0.167,0.156 10 false *1 3.833,2.427 4.01,2.604 0.177,0.177 10 false *a 1.604,1.677 1.833,1.865 0.229,0.188 10 false (A) 3.292,1.76 3.521,1.948 0.229,0.188 10 false (A) 5.917,2.052 6.083,2.208 0.167,0.156 10 false *1

Text in Illustration
*1 White Housing Lock - -
*a Slide - -

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the side No. 2 airbag sensor assembly has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the side No. 2 airbag sensor assembly, be careful that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the pin (stopper) is securely inserted into the body hole.

·

Tighten the bolt while holding the side No. 2 airbag sensor assembly because the side No. 2 airbag sensor assembly pin (stopper) is easily damaged.




e.

Connect the connector to the side No. 2 airbag sensor assembly.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.




f.

Check that there is no looseness in the installation parts of the side No. 2 airbag sensor assembly.


Hide 64740C 2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY

Hide 73350 4.CONNECT REAR NO. 2 SEAT OUTER BELT ASSEMBLY (for Lower Side)

Hide 73370C 5.CONNECT REAR NO. 1 SEAT OUTER BELT ASSEMBLY

Hide 64713F 6.INSTALL FRONT DECK SIDE TRIM COVER

Hide 58460D 7.INSTALL LUGGAGE HOLD BELT STRIKER ASSEMBLY

Hide 62332A 9.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 12.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 13.INSTALL REAR NO. 2 SEAT ASSEMBLY

Hide 64910J 14.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)