Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM J

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  Power Source Circuit  


DESCRIPTION

This circuit supplies power to the seat belt control ECU.

WIRING DIAGRAM

E228702E06
4.24,1.104 4.542,1.281 0.302,0.177 10 false PSB 5.74,0.938 5.917,1.115 0.177,0.177 10 false L2 5.031,0.938 5.24,1.115 0.208,0.177 10 false 2A 1.729,1.115 2.188,1.292 0.458,0.177 10 false DC/DC 6.094,0.938 6.302,1.115 0.208,0.177 10 false +B 6.094,1.417 6.375,1.594 0.281,0.177 10 false IG1 6.094,1.896 6.531,2.073 0.438,0.177 10 false PGND 5.104,0.719 5.198,0.896 0.094,0.177 10 false 5 5.073,1.198 5.25,1.375 0.177,0.177 10 false 16 5.802,0.719 5.896,0.896 0.094,0.177 10 false 7 5.74,1.406 5.917,1.583 0.177,0.177 10 false L3 5.042,1.406 5.24,1.583 0.198,0.177 10 false 2B 5.802,1.198 5.896,1.375 0.094,0.177 10 false 8 5.75,1.885 5.927,2.063 0.177,0.177 10 false L2 5.802,1.677 5.896,1.854 0.094,0.177 10 false 8 2.615,0.719 2.708,0.896 0.094,0.177 10 false 1 3.958,1.573 4.875,1.75 0.917,0.177 10 false ECU-IG NO. 2 2.917,1.417 3.698,1.823 0.781,0.406 10 false from IG1 NO. 1 Relay 0.271,0.896 1.125,1.229 0.854,0.333 10 false from Auxiliary Battery 2.563,0.938 2.771,1.115 0.208,0.177 10 false 2E 2.865,2.438 4.521,2.802 1.656,0.365 10 false Instrument Panel Junction Block Assembly 5.667,2.458 7.094,2.823 1.427,0.365 10 false Seat Belt Control ECU

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
IG SW Power switch IG signal/ON or OFF ON: Power switch on (IG)
OFF: Power switch off
-

OK:

Normal conditions listed above are displayed.




OK

2.CHECK HARNESS AND CONNECTOR (PGND CIRCUIT)

NG

2.CHECK HARNESS AND CONNECTOR (PGND CIRCUIT)
a.
U191310E01
1.098,2.321 1.297,2.484 0.199,0.163 10 L2 2.27,2.543 1.849,2.963 false 1.553,2.973 1.978,3.136 0.425,0.163 10 PGND 0.121,0.101 0.352,0.264 0.231,0.163 10 *a

Disconnect the L2 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-8 (PGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)


c.

Reconnect the L2 seat belt control ECU connector.



OK

3.CHECK HARNESS AND CONNECTOR (IG1 CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (IG1 CIRCUIT)
a.
U191315E01
0.372,2.426 0.571,2.588 0.199,0.163 10 L3 1.338,2.679 1.786,2.975 false 1.645,2.985 1.896,3.148 0.252,0.163 10 IG1 0.065,0.069 0.295,0.231 0.231,0.163 10 *a

Disconnect the L3 seat belt control ECU connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L3-8 (IG1) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)


d.

Reconnect the L3 seat belt control ECU connector.



OK

4.CHECK HARNESS AND CONNECTOR (+B CIRCUIT)

NG

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - SEAT BELT CONTROL ECU)
4.CHECK HARNESS AND CONNECTOR (+B CIRCUIT)
a.
U191311E02
2.01,2.563 1.594,2.979 false 1.115,2.333 1.396,2.552 0.281,0.219 10 false L2 1.448,2.99 1.677,3.156 0.229,0.167 10 false +B 0.125,0.094 0.354,0.26 0.229,0.167 10 false *a

Disconnect the L2 seat belt control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L2-7 (+B) - Body ground Power switch off 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Seat Belt Control ECU)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - SEAT BELT CONTROL ECU)
5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - SEAT BELT CONTROL ECU)
a.

Disconnect the 2A and 2B instrument panel junction block assembly connectors.


b.

Disconnect the L3 seat belt control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2A-5 - L2-7 (+B) Always Below 1 Ω
2B-16 - L3-8 (IG1) Always Below 1 Ω
L2-7 (+B) - Body ground Always 10 kΩ or higher
L3-8 (IG1) - Body ground Always 10 kΩ or higher




OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR