Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2001  Short to GND in Seat Belt Motor RH Circuit  


DESCRIPTION

The seat belt control ECU receives information from the driving support ECU assembly using CAN communication and tightens the seat belt by operating the motor in the front seat outer belt assembly RH.

DTC No. DTC Detection Condition Trouble Area
B2001 Short to ground in the seat belt motor RH circuit continues for 1 second or more.
·

Front seat outer belt assembly RH

·

Wire harness or connector (seat belt control ECU - front seat outer belt assembly RH)

·

Seat belt control ECU



WIRING DIAGRAM

E228695E03
5.345,2.041 5.571,2.215 0.226,0.174 10 L2 5.345,2.2 6.746,2.374 1.401,0.174 10 Seat Belt Control ECU 1.81,0.526 2.199,0.700 0.389,0.174 10 MOR- 2.73,0.526 3.155,0.700 0.424,0.174 10 MOR+ 5.617,1.721 6.007,1.896 0.390,0.174 10 MOR- 5.617,0.607 6.041,0.782 0.424,0.174 10 MOR+ 3.236,0.526 3.333,0.700 0.098,0.174 10 1 5.431,0.526 5.529,0.700 0.098,0.174 10 2 5.431,1.627 5.529,1.801 0.098,0.174 10 1 1.633,0.524 1.730,0.699 0.098,0.174 10 2 1.348,0.82 1.574,0.994 0.226,0.174 10 S7 1.348,0.978 3.594,1.310 2.246,0.332 10 Front Seat Outer Belt Assembly RH

CAUTION / NOTICE / HINT

CAUTION:

The pretensioner is built into the front seat outer belt assembly RH. Be sure to follow the correct inspection procedure, as failure to follow the correct procedure (such as inspection of incorrect connectors) may deploy the pretensioner.


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.INSPECT FRONT SEAT OUTER BELT ASSEMBLY RH
a.
U191308E01
0.696,3.236 0.895,3.398 0.199,0.163 10 S7 1.421,3.423 1.001,3.844 false 1.589,3.423 2.01,3.844 false 0.756,3.854 1.220,4.017 0.464,0.163 10 MOR- 1.77,3.854 2.239,4.017 0.469,0.163 10 MOR+ 0.164,0.15 0.396,0.313 0.232,0.163 10 *a

Disconnect the S7 front seat outer belt assembly RH connector.

HINT:

Do not remove the front seat outer belt assembly RH.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S7-1 (MOR+) - Body ground Always 1 MΩ or higher
S7-2 (MOR-) - Body ground Always 1 MΩ or higher



Text in Illustration
*a Component without harness connected
(Front Seat Outer Belt Assembly RH)

CAUTION:

Do not check a wrong connector.



OK

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY RH - SEAT BELT CONTROL ECU)

NG

REPLACE FRONT SEAT OUTER BELT ASSEMBLY RH

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY RH - SEAT BELT CONTROL ECU)
a.

Disconnect the L2 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-1 (MOR-) - Body ground Always 1 MΩ or higher
L2-2 (MOR+) - Body ground Always 1 MΩ or higher




OK

REPLACE SEAT BELT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY RH - SEAT BELT CONTROL ECU)