Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2006  Short to GND in Seat Belt Motor LH Circuit  


DESCRIPTION

The seat belt control ECU receives information from the driving support EC assembly using CAN communication and tightens the seat belt by operating the motor in the front seat outer belt assembly LH.

DTC No. DTC Detection Condition Trouble Area
B2006 Short to ground in the seat belt motor LH circuit continues for 1 second or more.
·

Front seat outer belt assembly LH

·

Wire harness or connector (seat belt control ECU - front seat outer belt assembly LH)

·

Seat belt control ECU



WIRING DIAGRAM

E228696E03
5.344,2.035 5.570,2.210 0.226,0.174 10 L2 5.344,2.194 6.745,2.369 1.401,0.174 10 Seat Belt Control ECU 1.804,0.522 2.170,0.697 0.365,0.174 10 MOL- 2.753,0.522 3.153,0.697 0.401,0.174 10 MOL+ 5.616,1.716 6.005,1.890 0.390,0.174 10 MOL- 5.606,0.611 6.030,0.786 0.424,0.174 10 MOL+ 3.234,0.522 3.332,0.697 0.098,0.174 10 1 5.43,0.52 5.527,0.695 0.098,0.174 10 3 5.43,1.621 5.527,1.796 0.098,0.174 10 4 1.631,0.522 1.729,0.697 0.098,0.174 10 2 1.401,0.814 1.627,0.989 0.226,0.174 10 R8 1.401,0.973 3.631,1.305 2.230,0.332 10 Front Seat Outer Belt Assembly LH

CAUTION / NOTICE / HINT

CAUTION:

The pretensioner is built into the front seat outer belt assembly LH. Be sure to follow the correct inspection procedure, as failure to follow the correct procedure (such as inspection of incorrect connectors) may deploy the pretensioner.


NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


PROCEDURE

1.INSPECT FRONT SEAT OUTER BELT ASSEMBLY LH
a.
U191309E01
0.696,3.236 0.895,3.398 0.199,0.163 10 R8 1.421,3.423 1.001,3.844 false 1.589,3.423 2.01,3.844 false 0.756,3.854 1.177,4.017 0.421,0.163 10 MOL- 1.77,3.854 2.224,4.017 0.454,0.163 10 MOL+ 0.254,0.298 0.458,0.461 0.204,0.163 10 *a

Disconnect the R8 front seat outer belt assembly LH connector.

HINT:

Do not remove the front seat outer belt assembly LH.



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R8-1 (MOL+) - Body ground Always 1 MΩ or higher
R8-2 (MOL-) - Body ground Always 1 MΩ or higher



Text in Illustration
*a Component without harness connected
(Front Seat Outer Belt Assembly LH)

CAUTION:

Do not check a wrong connector.



OK

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY LH - SEAT BELT CONTROL ECU)

NG

REPLACE FRONT SEAT OUTER BELT ASSEMBLY LH

2.CHECK HARNESS AND CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY LH - SEAT BELT CONTROL ECU)
a.

Disconnect the L2 seat belt control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-3 (MOL+) - Body ground Always 1 MΩ or higher
L2-4 (MOL-) - Body ground Always 1 MΩ or higher




OK

REPLACE SEAT BELT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT SEAT OUTER BELT ASSEMBLY LH - SEAT BELT CONTROL ECU)