Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2016.05–2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U0235  Lost Communication with Cruise Control Front Distance Range Sensor  U1002  Lost Communication with Gateway Module  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

The driving support ECU assembly sends vehicle speed and vehicle condition information to the millimeter wave radar sensor assembly. The millimeter wave radar sensor assembly then sends information on the presence, distance, and relative speed of objects ahead to the driving support ECU assembly. The driving support ECU assembly sends this information to the ECM and performs pre-crash system operation.

DTC No. DTC Detection Condition Trouble Area
U0235 When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and the driving support ECU assembly is detected for 1.7 seconds or more.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


U1002 When the power switch is on (IG), a communication error between the millimeter wave radar sensor assembly and driving support ECU assembly is detected for 1.7 seconds or more.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly


U1104 When the power switch is on (IG), a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for 1.2 seconds or more.
·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

E287467E13
1.76,1.344 2.927,1.646 1.167,0.302 10 false ECU-IG NO. 2 6,0.448 6.302,0.698 0.302,0.25 10 false B 2.813,1.052 3.01,1.302 0.198,0.25 10 false 5 3.021,1.969 3.479,2.25 0.458,0.281 10 false SGND 2.813,1.854 2.969,2.073 0.156,0.219 10 false 1 3.865,1.271 4.323,1.552 0.458,0.281 10 false CA1P 6,1.281 6.458,1.563 0.458,0.281 10 false CA1P 3.854,1.896 4.313,2.177 0.458,0.281 10 false CA1N 5.99,1.896 6.448,2.177 0.458,0.281 10 false CA1N 4.333,1.104 4.531,1.333 0.198,0.229 10 false 3 4.333,1.708 4.531,1.938 0.198,0.229 10 false 2 5.708,1.094 5.906,1.323 0.198,0.229 10 false 40 5.719,1.719 5.917,1.948 0.198,0.229 10 false 18 5.719,2.323 6.24,2.635 0.521,0.313 10 false L60 5.719,2.5 7.01,3.115 1.292,0.615 10 false Driving Support ECU Assembly 2.917,2.375 3.25,2.625 0.333,0.25 10 false A76 2.917,2.552 4.375,3.219 1.458,0.667 10 false Millimeter Wave Radar Sensor Assembly 1.198,3.427 3.167,3.656 1.969,0.229 10 false : CAN Communication Line 3.448,0.427 5.25,0.885 1.802,0.458 10 false from ECU-IG NO. 2 Fuse 3.042,1.177 3.344,1.427 0.302,0.25 10 false IGB 5.688,0.333 5.885,0.563 0.198,0.229 10 false 30 0.292,1.177 1.281,1.615 0.99,0.438 10 false from IG1 NO. 1 Relay

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Confirm that the connector is securely connected, as a partially connected connector is suspected for the cause of this DTC.



PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


e.

Check for DTCs.

Result:
Result Proceed to
CAN communication system DTCs are output A
CAN communication system DTCs are not output B




A

2.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)

B

2.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
U155140E01
1.558,0.405 1.875,0.573 0.317,0.168 10 L60 1.774,1.893 1.975,2.698 false 1.957,2.704 2.382,2.859 0.425,0.156 10 B 0.149,0.062 0.433,0.230 0.284,0.168 10 *a

Disconnect the L60 driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-30 (B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)

NG

REPAIR OR REPLACE POWER SOURCE CIRCUIT

3.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY POWER SOURCE)
a.
U191160E01
1.607,0.301 1.894,0.465 0.287,0.163 10 A76 2.642,0.546 3.030,0.685 0.388,0.139 10 IGB 0.052,0.044 0.365,0.183 0.314,0.139 10 *a 2,1.155 2.438,0.633 2.438,0.633 2.578,0.633 false 1.39,1.155 0.988,0.633 0.988,0.633 0.859,0.633 false 0.339,0.546 0.825,0.743 0.486,0.197 10 SGND

Disconnect the A76 millimeter wave radar sensor assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A76-1 (SGND) - Body ground Always Below 1 Ω



d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A76-5 (IGB) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - DRIVING SUPPORT ECU)
a.

Disconnect the A76 millimeter wave radar sensor assembly connector.


b.

Disconnect the L60 driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A76-3 (CA1P) - L60-40 (CA1P) Always Below 1 Ω
A76-2 (CA1N) - L60-18 (CA1N) Always Below 1 Ω
A76-3 (CA1P) or L60-40 (CA1P) - Body ground Always 10 kΩ or higher




OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).



NEXT

6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

7.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
7.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.


e.

Check for DTCs.


Result:
Result Proceed to
DTC U0235, U1002 and U1104 are not output A
DTC U0235, U1002 or U1104 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY