Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  B2074  Driver Side Seat Belt Buckle Switch Circuit Malfunction  


DESCRIPTION

This DTC is stored when there is a short or open in the front seat inner belt buckle switch circuit (for driver side).

DTC No. DTC Detection Condition Trouble Area
B2074 Open or short in front seat inner belt (buckle switch) circuit
·

CAN communication system

·

Front seat inner belt assembly LH (for LHD)

·

Front seat inner belt assembly RH (for RHD)

·

Seat belt control ECU Assembly

·

Wire harness or connector



WIRING DIAGRAM

E224693E02
0.602,2.097 2.810,2.266 2.208,0.169 10 Front Seat Inner Belt Assembly LH 4.38,2.097 6.464,2.266 2.083,0.169 10 Seat Belt Control ECU Assembly 4.38,1.946 4.583,2.116 0.202,0.169 10 L3 4.801,1.64 5.188,1.809 0.386,0.169 10 LBL- 4.801,0.544 5.188,0.714 0.386,0.169 10 LBL+ 4.618,1.561 4.719,1.730 0.101,0.169 10 6 4.618,0.449 4.719,0.618 0.101,0.169 10 5 2.378,1.561 2.764,1.730 0.387,0.169 10 LBE- 2.378,0.449 2.764,0.618 0.387,0.169 10 LBE+ 2.825,1.561 2.926,1.730 0.101,0.169 10 4 2.825,0.449 2.926,0.618 0.101,0.169 10 5 0.602,1.946 0.898,2.116 0.296,0.169 10 R33 0.102,0.055 0.767,0.437 0.665,0.383 12 for LHD:

E224692E04
0.619,2.1 2.826,2.269 2.208,0.169 10 Front Seat Inner Belt Assembly RH 4.397,2.1 6.481,2.269 2.083,0.169 10 Seat Belt Control ECU Assembly 4.397,1.949 4.693,2.118 0.296,0.169 10 L3 4.818,0.522 5.205,0.691 0.387,0.169 10 RBL- 4.827,1.63 5.214,1.800 0.387,0.169 10 RBL+ 4.635,0.442 4.736,0.612 0.101,0.169 10 3 4.644,1.535 4.745,1.705 0.101,0.169 10 4 2.394,0.452 2.781,0.621 0.387,0.169 10 RBE- 2.841,0.452 2.942,0.621 0.101,0.169 10 4 0.619,1.949 0.915,2.118 0.296,0.169 10 S23 0.104,0.072 0.861,0.299 0.757,0.228 12 for RHD: 2.394,1.563 2.781,1.733 0.387,0.169 10 RBE+ 2.841,1.563 2.942,1.733 0.101,0.169 10 5

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FRONT SEAT INNER BELT - SEAT BELT CONTROL ECU)
a.

Disconnect the R33 front seat inner belt assembly LH connector (for LHD).


b.

Disconnect the S23 front seat inner belt assembly RH connector (for RHD).


c.

Disconnect the L3 seat belt control ECU connector.


d.

Measure the resistance of the wire harness side connectors.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
R33-4 (LBE-) - L3-6 (LBL-) Always Below 1 Ω
R33-5 (LBE+) - L3-5 (LBL+) Always Below 1 Ω
R33-4 (LBE-) - Body ground Always 10 kΩ or higher
R33-5 (LBE+) - Body ground Always 10 kΩ or higher


Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
S23-4 (RBE-) - L3-3 (RBL-) Always Below 1 Ω
S23-5 (RBE+) - L3-4 (RBL+) Always Below 1 Ω
S23-4 (RBE-) - Body ground Always 10 kΩ or higher
S23-5 (RBE+) - Body ground Always 10 kΩ or higher



e.

Reconnect the L3 seat belt control ECU connector.


f.

Reconnect the S23 front seat inner belt assembly RH connector (for RHD).


g.

Reconnect the R33 front seat inner belt connector (for LHD).



OK

2.CHECK SEAT BELT CONTROL ECU

NG

REPLACE SEAT BELT CONTROL ECU

2.CHECK SEAT BELT CONTROL ECU
a.
U191243E02
2.281,1.292 1.969,0.729 false 2.375,1.313 2.688,0.75 false 2.458,1.458 2.135,2.021 false 2.531,1.438 2.844,2 false 0.177,0.146 0.531,0.406 0.354,0.26 10 false *a 2.385,0.25 2.635,0.417 0.25,0.167 10 false L3 0.688,2.344 2.156,2.552 1.469,0.208 10 false Buckle switch installed 1.76,0.5 2.156,0.688 0.396,0.188 10 false RBL+ 2.604,0.531 3.01,0.74 0.406,0.208 10 false RBL- 2.969,3.583 3.375,3.865 0.406,0.281 10 false GND 1.958,2.052 2.354,2.24 0.396,0.188 10 false LBL- 2.698,2.021 3.104,2.229 0.406,0.208 10 false LBL+

Fasten the driver side seat belt.


b.

Turn the power switch on (IG).


c.

Using an oscilloscope, check the waveform of the seat belt control ECU between the connector terminals.

HINT:

Voltage is only output for 20 ms of a 100 ms cycle.


Item Contents
Terminal L3-5 (LBL+) - L3-6 (LBL-) (for LHD)
L3-3 (RBL+) - L3-4 (RBL-) (for RHD)
Tool setting 2V/DIV, 20ms/DIV
Vehicle Condition Power switch on (IG)

Text in Illustration
*a Seat Belt Control ECU

OK:

Approximately 5 V



d.

Proceed to the next step based on the inspection result.

Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

REPAIR OR REPLACE HARNESS OR CONNECTOR (FRONT SEAT INNER BELT - SEAT BELT CONTROL ECU)

B

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH (for LHD)

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (for RHD)