Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2014.11–2017.12
RM2070E _58 Vehicle Interior _061943 PRE-CRASH SAFETY _0301811 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4A  Skid Control Buzzer Circuit  


DESCRIPTION

Based on pre-crash control, the driving support ECU assembly provides warnings to the driver. The driving support ECU assembly does this by sending a request signal to the millimeter wave radar sensor assembly to sound the skid control buzzer assembly.

When the millimeter wave radar sensor assembly detects a malfunction in the skid control buzzer assembly circuit, a malfunction signal is sent to the driving support ECU assembly, and this DTC is stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4A Skid Control Buzzer Circuit While the power switch is on (IG), a skid control buzzer assembly circuit malfunction signal is received from the millimeter wave radar sensor assembly for 3 seconds or more.
·

Skid control buzzer assembly

·

Wire harness or connector

·

Millimeter wave radar sensor assembly

·

Driving support ECU assembly



WIRING DIAGRAM

B381511E13
3.313,1.417 4.729,1.896 1.417,0.479 10 false Millimeter Wave Radar Sensor Assembly 5.719,1.438 6.719,1.833 1,0.396 10 false Driving Support ECU Assembly 1.417,1.146 2.698,1.573 1.281,0.427 10 false Skid Control Buzzer Assembly 5.719,1.281 6.104,1.438 0.385,0.156 10 false L60 5.792,0.469 6.344,0.646 0.552,0.177 10 false CA1P 5.792,0.958 6.344,1.135 0.552,0.177 10 false CA1N 4.021,0.469 4.573,0.646 0.552,0.177 10 false CA1P 4,0.948 4.552,1.125 0.552,0.177 10 false CA1N 4.479,0.323 5.031,0.5 0.552,0.177 10 false 3 4.479,0.802 5.031,0.979 0.552,0.177 10 false 2 5.542,0.333 6.094,0.51 0.552,0.177 10 false 40 5.542,0.802 6.094,0.979 0.552,0.177 10 false 18 3.615,0.698 4.167,0.885 0.552,0.188 10 false BZ 3.344,0.573 3.896,0.76 0.552,0.188 10 false 10 2.469,0.583 3.021,0.771 0.552,0.188 10 false 1 1.656,0.583 2.208,0.771 0.552,0.188 10 false 2 1.823,0.698 2.375,0.885 0.552,0.188 10 false IG1 2.219,0.698 2.771,0.885 0.552,0.188 10 false BZ 1.438,0.969 1.99,1.156 0.552,0.188 10 false L46 0.458,0.698 1.375,1.156 0.917,0.458 10 false From ECU-IG NO. 2 Fuse 0.802,2.292 2.99,2.479 2.188,0.188 10 false : CAN Communication Line 3.313,1.26 3.865,1.448 0.552,0.188 10 false A76

CAUTION / NOTICE / HINT

NOTICE:
·

When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).

·

Before performing the inspection, check that DTC U0235, U1002 or U1104 is not output.

·

Inspect the fuses for circuits related to this system before performing the following procedure.



PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (PCS CRASH ALARM BUZZER, PCS APPROACH ALARM BUZZER)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Pre-Crash 2 / Active Test.


e.

Perform Active Test according to the display on the GTS.

Pre-Crash 2
Tester Display Test Part Control Range Diagnostic Note
PCS Crash Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard
PCS Approach Alarm Buzzer Skid control buzzer assembly ON or OFF Buzzer can be heard


Result:
Result Proceed to
Skid control buzzer assembly does not sound A
Skid control buzzer assembly sounds B



A

2.INSPECT SKID CONTROL BUZZER ASSEMBLY

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY

2.INSPECT SKID CONTROL BUZZER ASSEMBLY
a.

Remove the skid control buzzer assembly (See page Vehicle Interior>PRE-CRASH SAFETY>PRE-CRASH SAFETY SYSTEM WARNING BUZZER>REMOVAL).


b.


OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER ASSEMBLY)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SKID CONTROL BUZZER ASSEMBLY)
a.
U154655E02
1.896,1.552 2.167,1.875 2.167,1.875 2.354,1.875 false 1.594,0.208 1.938,0.365 0.344,0.156 10 false L46 0.135,0.052 0.292,0.229 0.156,0.177 10 false *a 2.417,1.792 2.656,1.969 0.24,0.177 10 false IG1

Disconnect the L46 control buzzer assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L46-2 (IG1) - Body ground Power switch on (IG) 11 to 14 V
L46-2 (IG1) - Body ground Power switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control Buzzer Assembly)



OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL BUZZER ASSEMBLY - MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the L46 control buzzer assembly connector.


b.

Disconnect the A76 ter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L46-1 (BZ) - A76-10 (BZ) Always Below 1 Ω
L46-1 (BZ) or A76-10 (BZ) - Body ground Always 10 kΩ or higher




OK

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly with a new one (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL).



NEXT

6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Perform millimeter wave radar sensor assembly adjustment (See page Engine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT).



NEXT

7.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
7.CHECK DTC OUTPUT (PRE-CRASH SYSTEM)
a.

Using the GTS, enter the following menus: Body Electrical / Pre-Crash 2 / Trouble Codes.



c.

Recheck for DTCs.

OK:

DTC C1A4A is not output.




OK

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE DRIVING SUPPORT ECU ASSEMBLY