72526A
1.REMOVE RECLINING ADJUSTER RELEASE HANDLE
Using a screwdriver with its tip wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.
| *1 | Protective Tape |
72495
2.REMOVE VERTICAL ADJUSTING HANDLE (w/ Vertical Adjuster)
Remove the screw and vertical adjusting handle.
71812D
3.REMOVE FRONT SEAT CUSHION SHIELD
Remove the screw.
w/o Lumbar Support:
Disengage the 6 claws and clip, and remove the front seat cushion shield.
w/ Lumbar Support:
Disengage the 6 claws and clip.
Disconnect the connector.
Disengage the 5 clamps and remove the front seat cushion shield.
84920
4.REMOVE POWER SEAT SWITCH ASSEMBLY (w/ Lumbar Support)
73240
5.REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Driver Side)
73230
6.REMOVE FRONT SEAT INNER BELT ASSEMBLY (for Front Passenger Side)
71862
7.REMOVE FRONT SEAT INNER CUSHION SHIELD
Disengage the 5 claws and remove the front seat inner cushion shield.
8.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Disconnect the rubber band.
Disengage the fastener and separate the airbag wire harness.
w/ Seat Heater System:
Disengage the clamp and disconnect the seat heater wire harness.
Disengage the 4 hooks.
for 6 Way Seat Type:
Disengage the 2 hooks as shown in the illustration.
for 4 Way Seat Type:
Using a clip remover, remove the 2 clips.
Disengage each hook and remove the separate type front seat cushion cover with pad as shown in the illustration.
71072S
9.REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER
Remove the 2 hog rings.
Remove the 15 hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.
10.REMOVE SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Disengage the claw and 4 clamps to disconnect the airbag wire harness.
for Front Passenger Side:
Disengage the guide and disconnect the belt warning occupant detection sensor.
Remove the 5 hog rings.
Remove the 3 hog rings and disconnect the fastening rubber.
| *1 | Fastening Rubber |
Disengage the 4 claws and remove the 2 front seat headrest supports.
Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover.
Remove the separate type front seatback cover with pad from the front seatback spring assembly.
71074S
11.REMOVE SEPARATE TYPE FRONT SEATBACK COVER
Remove the 5 hog rings.
Remove the 2 hog rings and disconnect the fastening rubber from the separate type front seatback pad.
Remove the separate type front seatback cover from the separate type front seatback pad.
73920A
12.REMOVE FRONT SEAT AIRBAG ASSEMBLY
71875G
13.REMOVE RECLINING ADJUSTER INSIDE COVER LH
Disengage the guide and remove the reclining adjuster inside cover LH.
71876
14.REMOVE RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure as for the LH side.
71874
15.REMOVE FRONT SEAT LOWER CUSHION SHIELD LH (w/ Vertical Adjuster)
Disengage the hook as shown in the illustration.
Remove the screw.
Disengage the clip and remove the front seat lower cushion shield LH.
71873
16.REMOVE FRONT SEAT LOWER CUSHION SHIELD RH (w/ Vertical Adjuster)
Use the same procedure as for the LH side.
71537F
17.REMOVE NO. 2 FRONT SEAT CUSHION PROTECTOR
Remove the screw.
Disengage the 2 guides and remove the No. 2 front seat cushion protector.
71537E
18.REMOVE NO. 1 FRONT SEAT CUSHION PROTECTOR
Use the same procedure as for the No. 2 front seat cushion protector.
82168
19.REMOVE NO. 2 SEAT WIRE (w/ Lumbar Support)
for LHD:
Disengage the 4 clamps.
for RHD:
Disengage the 2 clamps.
Disconnect the connector.
Disengage the 2 clamps and remove the No. 2 seat wire with front seat wire.
Disconnect the connector to remove the No. 2 seat wire from the front seat wire.
71640S
20.REMOVE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
Remove the 4 bolts and separate type front seatback spring assembly from the separate type front seat cushion spring assembly.
72211C
21.REMOVE SEAT TRACK ADJUSTING HANDLE
Disengage the 2 hooks and remove the seat track adjusting handle from the separate type front seat cushion spring assembly.