Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for Center)
RM2070E _58 Vehicle Interior _061944 SEAT _0301817 REAR NO. 1 SEAT ASSEMBLY(for Center) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for Center)  REASSEMBLY  


PROCEDURE

Hide 72173B 1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE

a.
B314629E02
2.229,3.5 2.417,3.958 true 1.844,3.323 1.583,3.979 true 1.031,3.177 1.24,2.865 true 2.417,3.99 2.635,4.208 0.219,0.219 10 false *1 1.208,2.688 1.427,2.906 0.219,0.219 10 false *2 1.51,3.99 1.729,4.208 0.219,0.219 10 false *a

Insert the rear seat track adjusting handle into the rear seat adjuster and pass it through the 2 No. 1 plate springs.

Text in Illustration
*1 No. 1 Plate Spring
*2 No. 2 Plate Spring
*a Rear Seat Track Adjusting Handle Claw


b.

Engage the 2 No. 2 plate springs with the 2 rear seat track adjusting handle claws to install the rear seat track adjusting handle to the rear seat cushion frame sub-assembly.


Hide 71018 2.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY

a.
B314626

Install the rear seatback frame sub-assembly to the rear seat cushion frame sub-assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 72590B 3.INSTALL RECLINING REMOTE CONTROL CABLE ASSEMBLY

a.
B314625

Engage the 2 cable clamps to install the reclining remote control cable assembly.


Hide 71639 4.INSTALL REAR SEAT CUSHION HINGE COVER LH

a.
B314624E02
1.865,1.448 2.208,1.719 0.344,0.271 10 false <A> 0.823,1.51 1.167,1.781 0.344,0.271 10 false <A> 1.573,3.115 1.854,3.292 0.281,0.177 10 true <B>

Engage the guide <B> as shown in the illustration.


b.

Engage the claw.


c.

Engage the 2 guides <A> to install the rear seat cushion hinge cover LH.


Hide 71629A 5.INSTALL REAR SEAT CUSHION HINGE COVER RH

a.
B314621E02
1.385,1.542 1.677,1.708 0.292,0.167 10 false <A> 2.302,1.521 2.594,1.688 0.292,0.167 10 false <A> 1.563,3.125 1.875,3.302 0.313,0.177 10 true <B>

Engage the guide <B> as shown in the illustration.


b.

Engage the claw.


c.

Engage the 2 guides <A> to install the rear seat cushion hinge cover RH.


Hide 71834A 6.INSTALL REAR NO. 1 SEAT RECLINING COVER LH

a.
B314622

Engage the 2 claws to install the rear No. 1 seat reclining cover LH.


Hide 71833A 7.INSTALL REAR NO. 1 SEAT RECLINING COVER RH

HINT:

Use the same procedure as for the LH side.


Hide 79014 8.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY

a.
B314689

Using hog ring pliers, install the No. 1 seatback cover sub-assembly to the No. 1 seatback pad sub-assembly with 9 new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




Hide 9.INSTALL NO. 1 SEATBACK COVER WITH PAD

a.

Temporarily install the No. 1 seatback cover with pad to the rear seatback frame sub-assembly.


b.
B314618

Engage the 2 hooks.


c.
B314616

Engage the hook.

HINT:

Use the same procedure for the RH side and LH side.



d.
B314614

Engage the hook.

HINT:

Use the same procedure for the RH side and LH side.



e.
B314612

Using hog ring pliers, install 3 new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




f.
B314610

Using hog ring pliers, install 2 new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




g.

Engage the 4 hooks.


Hide 71931B 10.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY

a.
B292244

Engage the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.


Hide 72057 11.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B314608

Engage the 2 cable clamps.


b.
B314607

Engage the 2 guides to install the rear seat lock control lever sub-assembly.


c.

Install the 2 screws.


Hide 72615A 12.INSTALL REAR SEATBACK LOCK STRIKER COVER

a.
B315504

Engage the guide and claw to install the rear seatback lock striker cover.


Hide 71882A 13.INSTALL REAR SEATBACK BOARD

a.
B315506

Engage the 2 claws as shown in the illustration.


b.
B315505

Engage the 2 claws to install the rear seatback board as shown in the illustration.


Hide 79012 14.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY

a.
B314633

Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly to the No. 1 seat cushion pad sub-assembly with 16 new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




b.
B314631

Using hog ring pliers, install 6 new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, take care to minimize wrinkles as much as possible.




Hide 15.INSTALL NO. 1 SEAT CUSHION COVER WITH PAD

a.
B314603

Engage each hook to install the No. 1 seat cushion cover with pad.


b.
B314602

Engage the 5 hooks.


Hide 71865 16.INSTALL REAR NO. 1 SEAT BEZEL COVER

a.
B314601

Install the rear No. 1 seat bezel cover with the screw.


Hide 71829B 19.INSTALL REAR SEAT CUSHION MOULDING RH

a.
B314599

Engage the clip and 8 claws to install the rear seat cushion moulding RH.


b.

Install the 2 screws.


Hide 71826B 20.INSTALL REAR SEAT CUSHION MOULDING LH

a.
B314600

Engage the clip and 8 claws to install the rear seat cushion moulding LH.


b.

Install the 2 screws.


Hide 71848C 21.INSTALL SEAT ADJUSTER COVER CAP

a.
B314668

Install the seat adjuster cover cap.

HINT:

Use the same procedure for the RH side and LH side.