72173B
1.INSTALL REAR SEAT TRACK ADJUSTING HANDLE
Insert the rear seat track adjusting handle into the rear seat adjuster and pass it through the 2 No. 1 plate springs.
| *1 | No. 1 Plate Spring |
| *2 | No. 2 Plate Spring |
| *a | Rear Seat Track Adjusting Handle Claw |
Engage the 2 No. 2 plate springs with the 2 rear seat track adjusting handle claws to install the rear seat track adjusting handle to the rear seat cushion frame sub-assembly.
71018
2.INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY
Install the rear seatback frame sub-assembly to the rear seat cushion frame sub-assembly with the 4 bolts.
Engage the 2 cable clamps.
79956C
3.INSTALL REAR SEAT LEG SIDE COVER
Engage the guide and 2 claws to install the rear seat leg side cover.
72590B
4.INSTALL RECLINING REMOTE CONTROL CABLE ASSEMBLY
Engage the 2 cable clamps to install the reclining remote control cable.
Instal the 2 clamps.
72552E
5.INSTALL RECLINING HINGE COVER
Engage the guide <B> as shown in the illustration.
Engage the claw.
Engage the 2 guides <A> to install the reclining hinge cover.
71639
6.INSTALL REAR SEAT CUSHION HINGE COVER
Engage the guide <B> as shown in the illustration.
Engage the claw.
Engage the 2 guides <A> to install the rear seat cushion hinge cover.
71834B
7.INSTALL NO. 2 REAR SEAT RECLINING COVER
Engage the clip and 2 claws to install the No. 2 rear seat reclining cover.
71834A
8.INSTALL NO. 1 REAR SEAT RECLINING COVER
Use the same procedure as for the No. 2 rear seat reclining cover.
71876B
9.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Engage the 2 claws to install the reclining adjuster inside cover LH.
71875C
10.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure as for the LH side.
72526B
11.INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE
Engage the claw to install the No. 1 reclining adjuster release handle.
72597B
12.INSTALL NO. 1 RECLINING REMOTE CONTROL LEVER BEZEL
Engage the claw and guide to install the No. 1 reclining remote control lever bezel.
79014
13.INSTALL NO. 1 SEATBACK COVER SUB-ASSEMBLY
Using hog ring pliers, install the No. 1 seatback cover sub-assembly to the No. 1 seatback pad sub-assembly with 9 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
14.INSTALL NO. 1 SEATBACK COVER WITH PAD
Temporarily install the No. 1 seatback cover with pad to the rear seatback frame sub-assembly.
Engage the 2 hooks.
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Engage the 4 hooks.
71931B
15.INSTALL REAR NO. 1 SEAT HEADREST SUPPORT ASSEMBLY
Engage the 4 claws to install the 2 rear No. 1 seat headrest support assemblies.
72058A
16.INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY
Engage the 2 cable clamps.
Engage the 2 guides to install the rear seat lock control lever sub-assembly.
Install the 2 screws.
72590B
17.ADJUST RECLINING REMOTE CONTROL CABLE ASSEMBLY
Adjust the install position of reclining remote control cable as shown in the illustration.
| *1 | Tape (White) | *2 | Clamp |
| *a | Before Adjustment | *b | After Adjustment |
| *c | Pull | - | - |
72616A
18.INSTALL REAR SEATBACK LOCK STRIKER COVER
Engage the guide and claw to install the rear seatback lock striker cover.
71882A
19.INSTALL REAR SEATBACK BOARD
Engage the 2 claws as shown in the illustration.
Engage the 2 claws to install the rear seatback board as shown in the illustration.
79012
20.INSTALL NO. 1 SEAT CUSHION COVER SUB-ASSEMBLY
Using hog ring pliers, install the No. 1 seat cushion cover sub-assembly to the No. 1 seat cushion pad sub-assembly with 16 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
Using hog ring pliers, install 5 new hog rings.
Be careful not to damage the cover.
When installing the hog rings, take care to minimize wrinkles as much as possible.
21.INSTALL NO. 1 SEAT CUSHION COVER WITH PAD
Engage each hook to install the No. 1 seat cushion cover with pad.
Engage the 3 hooks.
71865
22.INSTALL REAR NO. 1 SEAT BEZEL COVER
Install the rear No. 1 seat bezel cover with the screw.
73390
23.INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY
71829B
24.INSTALL REAR SEAT CUSHION MOULDING RH
Engage the clip and 8 claws to install the rear seat cushion moulding RH.
Install the 2 screws.
71826B
25.INSTALL REAR SEAT CUSHION MOULDING LH
Engage the clip and 10 claws to install the rear seat cushion moulding LH.
Install the 2 screws.
72574A
26.INSTALL RECLINING CONTROL LEVER
Engage the claw to install the reclining control lever.
71849A
27.INSTALL SEAT ADJUSTER COVER CAP
Install the seat adjuster cover cap.
Use the same procedure for the RH side and LH side.