73920A
1.INSTALL FRONT SEAT AIRBAG ASSEMBLY
2.INSTALL SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY
Engage the 4 guides.
Install the separate type front seatback spring assembly to the separate type front seat cushion spring assembly with the 4 bolts.
71537F
3.INSTALL NO. 2 FRONT SEAT CUSHION PROTECTOR
Engage the 2 guides to install the No. 2 front seat cushion protector to the separate type front seatback spring assembly.
Install the screw.
71537E
4.INSTALL NO. 1 FRONT SEAT CUSHION PROTECTOR
Use the same procedure as for the No. 2 front seat cushion protector.
71874A
5.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH
Engage the clip to install the front seat lower cushion shield LH to the separate type front seat cushion spring assembly.
Install the screw.
Engage the hook as shown in the illustration.
71873A
6.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH
Use the same procedure as for the LH side.
71875G
7.INSTALL RECLINING ADJUSTER INSIDE COVER LH
Engage the 2 guides to install the reclining adjuster inside cover LH to the separate type front seatback spring assembly.
71876
8.INSTALL RECLINING ADJUSTER INSIDE COVER RH
Use the same procedure as for the LH side.
82168
9.INSTALL NO. 2 FRONT SEAT WIRE
Engage the 3 clamps to install the No. 2 front seat wire to the separate type front seatback spring assembly.
Connect the 2 connectors.
71074S
10.INSTALL SEPARATE TYPE FRONT SEATBACK COVER
Using hog ring pliers, connect the fastening rubber to the separate type front seatback pad with 2 new hog rings.
| *a | Fastening Rubber |
| *b | Hog Ring |
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install the separate type front seatback cover to the separate type front seatback pad with 5 new hog rings
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
11.INSTALL SEPARATE TYPE FRONT SEATBACK COVER WITH PAD
Temporarily install the separate type front seatback cover with pad to the separate type front seatback spring assembly.
Engage the 4 claws to install the 2 front seat headrest supports.
Install the bracket of the separate type front seatback cover with the nut.
For vehicles with side airbags, the separate type front seatback cover must be securely installed. Otherwise, the front seat airbag assembly may not deploy properly.
Make sure that the strap is not twisted after installing the nut.
Install the bracket of the separate type front seatback cover securely.
Turn back the separate type front seatback cover to its original position.
Using hog ring pliers, connect the 2 fastening rubbers to the front seatback spring with 3 new hog rings.
| *a | Fastening Rubber |
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 3 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seatback cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.
71072S
12.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER
Using hog ring pliers, install the separate type front seat cushion cover to the separate type front seat cushion pad with 15 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
Using hog ring pliers, install 2 new hog rings.
Be careful not to damage the separate type front seat cushion cover.
Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.
13.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER WITH PAD
Engage each hook as shown in the illustration to install the separate type front seat cushion cover with pad to the separate type front seat cushion spring assembly.
Engage the 2 hooks as shown in the illustration.
Engage the fastener to secure the side airbag wire harness.
Engage the clamp.
Connect the connector.
Engage the 3 clamps to secure the seat heater wire harness.
Engage the 4 hooks.
Connect the rubber band.
71862
14.INSTALL FRONT INNER SEAT CUSHION SHIELD
Engage the 5 claws to install the front inner seat cushion shield.
82192
15.INSTALL NO. 1 FRONT SEAT WIRE
Engage the 2 claws and 2 clamps to install the No. 1 front seat wire to the front seat cushion shield.
84920
16.INSTALL LUMBAR SWITCH (POWER SEAT SWITCH ASSEMBLY)
84922C
17.INSTALL FRONT POWER SEAT SWITCH
84921A
18.INSTALL RECLINING POWER SEAT SWITCH KNOB
Engage the 4 claws to install the reclining power seat switch knob.
84921B
19.INSTALL SLIDE AND VERTICAL POWER SEAT SWITCH KNOB
Engage the 4 claws to install the slide and vertical power seat switch knob.
20.INSTALL FRONT SEAT CUSHION SHIELD ASSEMBLY
Engage the clamp.
Connect the 2 connectors.
Engage the guide and 5 claws.
Engage the clip to install the front seat cushion shield assembly.
Engage the 6 clamps to connect the No. 1 front seat wire.
Connect the 4 connectors.
71849
21.INSTALL SEAT ADJUSTER COVER CAP
Install the 2 seat adjuster cover caps.
71868A
22.INSTALL FRONT INNER NO. 1 SEAT CUSHION SHIELD
Install the clip to the front inner No. 1 seat cushion shield.
Engage the 3 guides and 3 claws to install the front inner No. 1 seat cushion shield.
Engage the clip.
Install the screw.
73240
23.INSTALL FRONT SEAT INNER BELT ASSEMBLY