Home › Vehicle Interior › SEAT BELT › FRONT SEAT OUTER BELT ASSEMBLY › 2012.03–2013.08
RM2070E _58 Vehicle Interior _061945 SEAT BELT _0301827 FRONT SEAT OUTER BELT ASSEMBLY A

SEAT BELT  FRONT SEAT OUTER BELT ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure described below is for the LH side.



PROCEDURE

Hide 73200A 1.INSTALL FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY

a.
B283095E01
0.633,0.485 0.924,0.646 0.291,0.161 10 <B> 0.995,1.945 1.280,2.106 0.285,0.161 10 <A>

Engage the guide to temporarily install the front shoulder belt anchor adjuster assembly with the 2 bolts.


b.

Fully tighten the bolt <A> first, then the bolt <B> to install the front shoulder belt anchor adjuster assembly.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 73220 2.INSTALL FRONT SEAT OUTER BELT ASSEMBLY

a.
B283094E03
0.406,0.875 0.688,1.042 0.281,0.167 10 true <A> 0.448,1.802 0.729,1.969 0.281,0.167 10 false <B>

Temporarily install the front seat outer belt assembly with the 2 bolts.


b.

Fully tighten the bolt <A> first, then the bolt <B> to install the front seat outer belt assembly.

Torque:
Bolt <A> : 7.5 N*m (77 kgf*cm, 66 in.*lbf)
Bolt <B> : 42 N*m (428 kgf*cm, 31 ft.*lbf)


c.
B283096E03
0.833,1.198 1.031,1.365 0.198,0.167 10 true *A 0.74,1.604 0.938,1.771 0.198,0.167 10 true *1

Connect the pretensioner connector and lock the locking button as shown in the illustration.

Text in Illustration
*A w/ Pre-crash Safety System
*1 Pretensioner Connector

NOTICE:

Securely lock the locking button.



d.

Connect the connector.


e.

w/ Pre-crash Safety System:

i.

Connect the connector.



f.

Connect the shoulder anchor of the front seat outer belt assembly with the nut.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 62414A 4.INSTALL CENTER PILLAR LOWER GARNISH

Hide 73220 5.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

a.

Install the floor end of the front seat outer belt assembly with the bolt.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

Check if the ELR locks.

NOTICE:

The check should be performed with the outer belt assembly installed.


i.

With the belt assembly installed, check that the belt locks when it is pulled out quickly.



Hide 73233 6.INSTALL LAP BELT OUTER ANCHOR COVER

a.

Engage the 3 claws to install the lap belt outer anchor cover.


Hide 62332A 7.INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 62312B 9.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 11.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).