Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061945 SEAT BELT _0301836 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Driver Side Seat Belt Warning Light does not Operate  


DESCRIPTION

The combination meter sub-assembly blinks or turns off the seat belt warning light on the combination meter sub-assembly in accordance with the state of the front seat inner belt assembly (for Driver).

HINT:

The seat belt warning light on the combination meter sub-assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

B287218E53
0.615,2.469 2.979,2.688 2.365,0.219 10 false : CAN Communication Line 0.865,0.844 1.25,1.156 0.385,0.313 10 false CAN 0.219,1.573 1.365,1.76 1.146,0.188 10 false Meter Circuit Plate 1.635,1.708 3.271,2.292 1.635,0.583 10 false Main Body ECU (Multiplex Network Body ECU) 3.396,1.26 4.51,1.854 1.115,0.594 10 false Instrument Panel Junction Block Assembly 2.073,0.844 2.583,1.083 0.51,0.24 10 false CAN 1.625,1.563 2.125,1.969 0.5,0.406 10 false MB 4.188,0.833 4.49,1.094 0.302,0.26 10 false 2B 5.156,1.313 6.604,1.698 1.448,0.385 10 false Front Seat Inner Belt Assembly (for Driver) 5.198,1.135 6.198,1.333 1,0.198 10 false R33*1, S23*2 3.125,0.75 3.417,0.958 0.292,0.208 10 false 18 4.177,0.635 4.479,0.813 0.302,0.177 10 false 14 5.25,0.75 5.542,0.948 0.292,0.198 10 false 3 6.115,0.75 6.344,0.927 0.229,0.177 10 false 2 2.667,0.844 3.198,1.25 0.531,0.406 10 false DBKL 5.438,0.75 5.729,0.948 0.292,0.198 10 false + 5.906,0.76 6.198,0.958 0.292,0.198 10 false E 5.01,2.135 5.823,2.49 0.813,0.354 10 false *1: for LHD 5.01,2.438 5.854,2.698 0.844,0.26 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the communication system by checking communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Seat Buckle SW Driver seat belt buckle switch/ON or OFF ON: Driver seat belt fastened
OFF: Driver seat belt unfastened
-

OK:

ON or OFF appears on the tester screen according to the driver seat belt condition.




OK

2.PERFORM ACTIVE TEST USING GTS

NG

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)
2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter /Active Test.


e.

Perform the Active Test according to the display on the GTS.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Driver Side Seat Belt Seat belt warning light OFF/ON -

OK:

The seat belt warning light on the combination meter sub-assembly operates normally.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

3.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)
a.
B271232E04
0.205,0.166 0.357,0.303 0.151,0.137 10 *a

Remove the front seat inner belt assembly (for Driver) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 - 3 Driver seat belt unfastened Below 1 Ω
2 - 3 Driver seat belt fastened 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Front Seat Inner Belt Assembly (for Driver))



OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER)

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the main body ECU (multiplex network body ECU) (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).

U190821E01
0.14,0.097 0.342,0.283 0.202,0.186 10 *a 1.681,1.386 2.115,1.572 0.434,0.186 10 DBKL 2.26,1.091 2.26,1.47 2.26,1.47 2.076,1.47 false 1.902,0.57 2.174,0.726 0.272,0.156 10 MB 5.6,0.29 5.873,0.445 0.272,0.156 10 2B

Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)
- -


b.

Disconnect the 2B instrument panel junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
MB-18 (DBKL) - 2B-14 Always Below 1 Ω




OK

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER) - BODY GROUND)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - FRONT SEAT INNER BELT ASSEMBLY (FOR DRIVER) - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
2B-14 - R33-3 (+) Always Below 1 Ω
R33-3 (+) - Body ground Always 10 kΩ or higher
R33-2 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
2B-14 - S23-3 (+) Always Below 1 Ω
S23-3 (+) - Body ground Always 10 kΩ or higher
S23-2 (E) - Body ground Always Below 1 Ω




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR