Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2014.11–2020.08
RM2070E _58 Vehicle Interior _061945 SEAT BELT _0301836 SEAT BELT WARNING SYSTEM J

SEAT BELT  SEAT BELT WARNING SYSTEM  Front Passenger Side Seat Belt Warning Light Malfunction  


DESCRIPTION

The occupant detection sensor (separate type front seat cushion pad) detects if the passenger seat is occupied and sends signals to the combination meter sub-assembly. The front seat inner belt assembly (for Front Passenger) detects the passenger seat belt condition and sends signals to the combination meter sub-assembly. After receiving the signals from the occupant detection sensor (separate type front seat cushion pad) and front seat inner belt assembly (for Front Passenger), the seat belt warning light in the combination meter sub-assembly will blink or go off.

HINT:

The seat belt warning light on the combination meter sub-assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM

B275873E23
0.063,1.677 0.365,1.906 0.302,0.229 10 false L27 0.094,2.146 1.448,2.531 1.354,0.385 10 false Meter Circuit Plate*4 1.198,0.771 1.688,1.052 0.49,0.281 10 false SW 2.604,0.771 2.885,1.031 0.281,0.26 10 false R33 5.594,0.771 5.875,1.031 0.281,0.26 10 false S23 5.948,0.771 6.229,1.031 0.281,0.26 10 false R33 2.313,0.563 2.594,0.792 0.281,0.229 10 false 3 2.688,0.563 2.969,0.792 0.281,0.229 10 false 3 2.24,0.771 2.521,1.031 0.281,0.26 10 false S23 5.385,0.677 5.667,0.906 0.281,0.229 10 false E 6.042,0.563 6.323,0.792 0.281,0.229 10 false 2 3.052,1.135 3.24,1.344 0.188,0.208 10 false B 4.042,1.135 4.229,1.344 0.188,0.208 10 false B 2.781,1.125 2.969,1.333 0.188,0.208 11 false 1 3.781,1.125 3.969,1.333 0.188,0.208 11 false 3 2.5,1.875 4.865,2.344 2.365,0.469 10 false Occupant Detection Sensor (Separate Type Front Seat Cushion Pad) 4.354,1.167 6.271,1.604 1.917,0.438 10 false Front Seat Inner Belt Assembly (for Front Passenger) 2.396,2.479 4.521,2.708 2.125,0.229 10 false *3: w/ Multi-information Display 4.615,2.49 6.625,2.719 2.01,0.229 10 false *4: w/o Multi-information Display 1.656,0.656 1.969,0.865 0.313,0.208 10 false 29 2.271,0.979 2.552,1.208 0.281,0.229 10 false *1 2.656,0.979 2.938,1.208 0.281,0.229 10 false *2 5.604,0.979 5.885,1.208 0.281,0.229 10 false *1 6,0.979 6.281,1.208 0.281,0.229 10 false *2 3,0.667 3.281,0.896 0.281,0.229 10 false + 5.646,0.563 5.927,0.792 0.281,0.229 10 false 2 0.073,1.844 2.354,2.167 2.281,0.323 10 false Combination Meter Sub-assembly*3 0.323,2.479 1.094,2.698 0.771,0.219 10 false *1: for LHD 1.354,2.479 2.125,2.698 0.771,0.219 10 false *2: for RHD

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P-Seatbelt Buckle SW Front passenger seat belt buckle switch signal/ON or OFF ON: Front passenger seat belt unfastened
OFF: Front passenger seat belt fastened
-

Result:
Result Proceed to
ON or OFF does not appears on the tester screen according to the front passenger seat belt condition (w/ Multi-information Display) A
ON or OFF does not appears on the tester screen according to the front passenger seat belt condition (w/o Multi-information Display) B
ON or OFF appears on the tester screen according to the front passenger seat belt condition C




A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

C

2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER) - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (COMBINATION METER SUB-ASSEMBLY - FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER) - BODY GROUND)
a.

Disconnect the L27 combination meter sub-assembly connector.


b.

Disconnect the S23*1 or R33*2 front seat inner belt assembly (for Front Passenger) connector.


c.

Measure the resistance according to the value(s) in the table below.

*1: for LHD

*2: for RHD


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
L27-29 (SW) - S23-3 (+) Always Below 1 Ω
L27-29 (SW) - Body ground Always 10 kΩ or higher
S23-2 (E) - Body ground Always Below 1 Ω

for RHD
Tester Connection Condition Specified Condition
L27-29 (SW) - R33-3 (+) Always Below 1 Ω
L27-29 (SW) - Body ground Always 10 kΩ or higher
R33-2 (E) - Body ground Always Below 1 Ω




OK

3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)
a.
B218574E01
0.146,0.125 0.303,0.276 0.157,0.151 10 *a

Remove the occupant detection sensor (separate type front seat cushion pad) (See page Vehicle Interior>SEAT BELT>OCCUPANT DETECTION SENSOR>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 3 Front passenger seat occupied Below 100 Ω
1 - 3 Front passenger seat not occupied 1 MΩ or higher


Text in Illustration
*a Component without harness connected
(Occupant Detection Sensor (Separate Type Front Seat Cushion Pad))



OK

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)

NG

REPLACE OCCUPANT DETECTION SENSOR (SEPARATE TYPE FRONT SEAT CUSHION PAD)

4.INSPECT FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)
a.
U190849E02
0.177,0.104 0.333,0.406 0.156,0.302 10 false *a 1.146,0.625 1.458,0.792 0.313,0.167 10 false S23 1.479,0.635 1.792,0.813 0.313,0.177 10 false *A 1.854,0.625 2.167,0.802 0.313,0.177 10 false R33 2.208,0.635 2.51,0.833 0.302,0.198 10 false *B 1.677,2.917 1.844,3.188 0.167,0.271 10 false B

Remove the front seat inner belt assembly (for Front Passenger) (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
S23-3 - B-1 Always Below 1 Ω
S23-2 - B-3 Front passenger seat belt unfastened Below 1 Ω
S23-2 - B-3 Front passenger seat belt fastened 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
R33-3 - B-1 Always Below 1 Ω
R33-2 - B-3 Front passenger seat belt unfastened Below 1 Ω
R33-2 - B-3 Front passenger seat belt fastened 10 kΩ or higher


Text in Illustration
*A for LHD
*B for RHD
*a Component without harness connected
(Front Seat Inner Belt Assembly (for Front Passenger))

Result:
Result Proceed to
OK (w/ Multi-information Display) A
OK (w/o Multi-information Display) B
NG C




A

REPLACE COMBINATION METER SUB-ASSEMBLY

B

C

REPLACE FRONT SEAT INNER BELT ASSEMBLY (FOR FRONT PASSENGER)