Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM › 2012.03–2020.08
RM2070E _58 Vehicle Interior _061945 SEAT BELT _0301836 SEAT BELT WARNING SYSTEM G

SEAT BELT  SEAT BELT WARNING SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT DRIVER SEAT BELT WARNING SYSTEM

HINT:

The seat belt warning light on the combination meter sub-assembly is used for both the driver seat and front passenger seat.


a.

Turn the power switch on (IG).


b.

When the driver seat belt is not fastened, check that the seat belt warning light on the combination meter sub-assembly blinks.


c.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


d.

Power switch on (READY).


e.

When the driver seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter sub-assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter sub-assembly blinks at an interval of 0.4 seconds.


f.

When the driver seat belt is fastened, check that the seat belt warning light on the combination meter sub-assembly turns off.


Hide 2.INSPECT FRONT PASSENGER SEAT BELT WARNING SYSTEM

HINT:

The seat belt warning light on the combination meter sub-assembly is used for both the driver seat and front passenger seat.


a.

Turn the power switch on (IG).


b.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



c.

Fasten the driver seat belt.


d.

When the front passenger seat belt is not fastened, check that the seat belt warning light on the combination meter sub-assembly blinks.


e.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


f.

Power switch on (READY).


g.

When the front passenger seat is occupied, the front passenger seat belt is not fastened and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that the seat belt warning light on the combination meter sub-assembly blinks at an interval of 1.2 seconds for 30 seconds.

After that, check that the seat belt warning light on the combination meter sub-assembly blinks at an interval of 0.4 seconds.


h.

When the front passenger seat belt is fastened, check that the seat belt warning light on the combination meter sub-assembly turns off.


Hide 3.INSPECT REAR SEAT BELT WARNING

a.
B313255E01
0.207,0.197 0.361,0.334 0.154,0.137 10 *a 1.352,2.687 1.506,2.824 0.154,0.137 10 *b 1.683,2.687 1.824,2.824 0.141,0.137 10 *c 1.98,2.687 2.128,2.824 0.149,0.137 10 *d 1.49,3.058 1.639,3.195 0.149,0.137 10 *e 1.874,3.058 1.991,3.195 0.117,0.137 10 *f 1.435,2.065 1.435,2.667 false 1.575,2.288 1.575,3.048 false 1.927,2.288 1.927,3.048 false 1.753,2.065 1.753,2.667 false 2.063,2.065 2.063,2.667 false

Check the state of the rear seat belt warning light on the combination meter sub-assembly under the following conditions:

Text in Illustration
*a Rear Seat Belt Warning Light (Combination Meter Sub-assembly)
*b Rear No. 1 Seat LH
*c Rear No. 1 Seat Center
*d Rear No. 1 Seat RH
*e Rear No. 2 Seat LH
*f Rear No. 2 Seat RH

i.

Open and then close either rear door.


ii.

Turn the power switch on (IG).


iii.

When the rear seat belt is not fastened, check that the rear seat belt warning light on the combination meter sub-assembly illuminated.


iv.

After 34 seconds, check that the rear seat belt warning light on the combination meter sub-assembly turns off.


v.

When one of the rear seat belt is not fastened from fastened, check that the rear seat belt warning light on the combination meter sub-assembly illuminated.



Hide 4.INSPECT SEAT BELT WARNING BUZZER

HINT:

The seat belt warning buzzer can be customized. Make sure that this function is ON (See page Vehicle Interior>SEAT BELT>SEAT BELT WARNING SYSTEM>CUSTOMIZE PARAMETERS).


a.

Place a weight of 20 kg (44.0 lb) on the front passenger seat.

NOTICE:

Place the weight on the seat cushion and do not allow it to come into contact with the seatback.



b.

Lift up the vehicle using a swing arm type lift (See page General>INTRODUCTION>REPAIR INSTRUCTION>VEHICLE LIFT AND SUPPORT LOCATIONS).


c.

Power switch on (READY).


d.

Check that the seat belt warning buzzer in the combination meter sub-assembly sounds at an interval of 1.2 seconds for 30 seconds.


e.

After the seat belt warning buzzer has been sounding for 30 seconds at an interval of 1.2 seconds, check that the seat belt warning buzzer in the combination meter sub-assembly sounds at an interval of 0.4 seconds for 90 seconds.


f.

Check that the seat belt warning buzzer in the combination meter sub-assembly stops 2 minutes after it started sounding at an interval of 1.2 seconds.


g.

After the buzzer has stopped, turn the power switch off and then start the hybrid system again. Drive the vehicle at approximately 20 km/h (12 mph) or more while the driver, front passenger or rear seat belt is not fastened, and check that the buzzer sounds again.


h.

After the buzzer has stopped, fasten the driver, front passenger or rear seat belt. Drive the vehicle at approximately 20 km/h (12 mph) or more and unfasten the driver, front passenger or rear seat belt, and check that the buzzer sounds again.


i.

After the buzzer has stopped, stop the vehicle, move the shift lever to R, and then move it to D. Drive the vehicle at approximately 20 km/h (12 mph) or more, and check that the buzzer sounds again.