Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2012.03–2014.11
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1473/73  A/C Inverter Start-up Signal System Malfunction  


DESCRIPTION

The inverter activation signal is sent to the compressor with motor assembly from the power management control ECU. Compressor control is stopped and this DTC is stored if there is an open or short in the signal circuit.

DTC No. DTC Detection Condition Trouble Area
B1473/73 Open or short in A/C inverter start-up signal system
·

Harness or connector between power management control ECU and compressor with motor assembly

·

Compressor with motor assembly

·

Power management control ECU

·

Hybrid control system

·

CAN communication system



WIRING DIAGRAM

E230287E05
0.146,6.313 1.594,6.833 1.448,0.521 10 false Compressor with Motor Assembly 5.76,3.906 7,4.281 1.24,0.375 10 false Power Management Control ECU 6.104,1.865 6.396,2.01 0.292,0.146 10 false STB 6.104,2.885 6.396,3.031 0.292,0.146 10 false ITE 6.063,3.375 6.354,3.521 0.292,0.146 10 false CLK 6.104,2.354 6.344,2.5 0.24,0.146 10 false ETI 0.802,1.823 1.177,1.969 0.375,0.146 10 false STBI 0.896,2.865 1.156,3.01 0.26,0.146 10 false DIN 0.865,3.354 1.156,3.5 0.292,0.146 10 false CLK 0.896,3.927 1.156,4.073 0.26,0.146 10 false IG1 0.823,4.5 1.156,4.646 0.333,0.146 10 false GND 0.948,5.281 1.188,5.427 0.24,0.146 10 false PE 0.948,5.771 1.167,5.917 0.219,0.146 10 false PB 0.74,2.313 1.156,2.458 0.417,0.146 10 false DOUT 1.302,1.844 1.573,1.99 0.271,0.146 10 false D12 1.302,2.354 1.573,2.5 0.271,0.146 10 false D12 1.302,2.865 1.573,3.01 0.271,0.146 10 false D12 1.302,3.354 1.573,3.5 0.271,0.146 10 false D12 1.302,4.5 1.573,4.646 0.271,0.146 10 false D12 1.302,3.917 1.573,4.063 0.271,0.146 10 false D12 5.781,1.719 6,1.927 0.219,0.208 10 false 20 5.792,2.229 6.031,2.438 0.24,0.208 10 false 30 5.792,2.74 6.083,2.948 0.292,0.208 10 false 31 5.781,3.25 5.969,3.396 0.188,0.146 10 false 19 4.927,7.219 7.094,7.479 2.167,0.26 10 false Inverter with Converter Assembly 5.188,5.677 5.292,5.823 0.104,0.146 10 false 1 5.188,5.146 5.292,5.313 0.104,0.167 10 false 2 1.354,5.281 1.563,5.427 0.208,0.146 10 false E1 1.344,5.781 1.583,5.927 0.24,0.146 10 false E1 1.385,5.052 1.49,5.198 0.104,0.146 10 false 1 1.385,5.573 1.49,5.74 0.104,0.167 10 false 2 1.385,1.625 1.49,1.771 0.104,0.146 10 false 4 1.385,2.135 1.49,2.302 0.104,0.167 10 false 3 1.385,2.625 1.49,2.771 0.104,0.146 10 false 2 1.385,3.146 1.49,3.313 0.104,0.167 10 false 1 1.385,3.719 1.49,3.865 0.104,0.146 10 false 6 1.385,4.271 1.49,4.438 0.104,0.167 10 false 5 5.438,5.146 5.844,5.292 0.406,0.146 10 false ACPE 5.438,5.646 5.844,5.792 0.406,0.146 10 false ACPB 5.719,5.948 6.219,6.5 0.5,0.552 10 false Electric Vehicle Fuse 2.698,4.094 2.99,4.24 0.292,0.146 10 false A/C 4.198,3.906 5.594,4.052 1.396,0.146 10 false from IG1 NO. 1 Relay 2.26,7.146 3.979,7.292 1.719,0.146 10 false : CAN Communication Line 4.927,7.042 5.177,7.25 0.25,0.208 10 false E3 5.76,3.74 6.479,3.969 0.719,0.229 10 false A21 0.177,1.063 2.448,1.26 2.271,0.198 10 false Air Conditioning Amplifier Assembly 2.729,6.323 3.938,6.552 1.208,0.229 10 false No. 2 Engine Wire

CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the flow chart for the hybrid control system first if any DTCs from those systems are output simultaneously.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.CHECK DIAGNOSTIC TROUBLE CODE

B

2.CHECK DIAGNOSTIC TROUBLE CODE
a.

Check if DTCs for the air conditioning system and the hybrid control system are output using the GTS.

Result:
Result Proceed to
Only DTC B1473 is output A
DTCs B1473 and P3108 are output simultaneously (B1498 is not output)
DTCs B1473 and B1498 are output simultaneously (P3108 is not output) B
DTCs B1473, B1498 and P3108 are output simultaneously
DTCs other than P3108 are output for hybrid control system C




A

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)

B

C

3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR ASSEMBLY)
CAUTION:

Do not disconnect the connector on the high-voltage side.


a.

Disconnect the A21 power management control ECU connector.


b.

Disconnect the D12 compressor with motor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-20 (STB) - D12-4 (STBI) Always Below 1 Ω
A21-20 (STB) - Body ground Always 10 kΩ or higher




OK

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT COMPRESSOR WITH MOTOR ASSEMBLY
a.

Reconnect the D12 compressor with motor assembly connector.


b.
U155097E01
0.147,0.106 0.334,0.269 0.187,0.163 10 *a 1.624,0.769 1.922,0.970 0.298,0.201 10 A21 1.071,3.018 1.379,3.172 0.309,0.154 10 STB 1.462,2.438 1.248,2.984 false

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-20 (STB) - Body ground Power switch on (IG) 11 to 14 V
A21-20 (STB) - Body ground Power switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Power Management Control ECU)



OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY