Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › 2014.11–2016.05
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B1475/75  A/C Inverter Cooling / Heating System Malfunction  


DESCRIPTION

The temperature sensor of the compressor with motor assembly detects its inverter temperature.

If the temperature exceeds the maximum, the compressor with motor assembly stops compressor operation, and this DTC will be stored.

DTC No. DTC Detection Condition Trouble Area
B1475/75 Temperature of the inverter is outside the specified range (temperature is too high), or there is an open or short to ground in the temperature sensor circuit.
·

Cooling fan system


·

Refrigerant volume


·

Compressor with motor assembly

·

CAN communication system



CAUTION / NOTICE / HINT

CAUTION:
·

Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.

·

Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.



NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the flow chart for the hybrid control system first if any DTCs from those systems are output simultaneously.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Use the GTS to check if the CAN communication system is functioning normally.

Result:
Result Proceed to
CAN DTC is not output A
CAN DTC is output B




A

2.PERFORM ACTIVE TEST USING GTS

B

2.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test.


e.

Check the operation by referring to the table below.


Engine and ECT
Tester Display Test Part Control Range Diagnostic Note
Control the Electric Cooling Fan Electric cooling fan OFF, ON -

OK:

Electric cooling fan operates smoothly.



OK

3.CHECK REFRIGERANT PRESSURE

NG

3.CHECK REFRIGERANT PRESSURE

b.
E050573

Read the manifold gauge pressure when the following conditions are established.

i.

Prepare the vehicle according to the chart below.

Item Condition
Power Switch on (READY)
Vehicle Doors Fully open
Temperature Setting MAX COLD
Blower Speed HI
A/C Switch On
R/F Switch RECIRCULATION
(30 to 35°C (86 to 95°F))

Standard Pressure:
Low pressure side:

0.15 to 0.25 MPa (1.5 to 2.5 kgf/cm2, 21.3 to 35.6 psi)

High pressure side:

1.37 to 1.57 MPa (14 to 16 kgf/cm2, 199 to 228 psi)




Result:
Result Proceed to
OK A
NG (for R-134a) B
NG (for R-1234yf) C



A

4.READ OUTPUT DTC (DTC B1475/75)

B

C

4.READ OUTPUT DTC (DTC B1475/75)

b.

Prepare the vehicle according to the table below.

Item Condition
Engine speed Engine idling
Blower speed HI
A/C Switch On
Temperature setting MAX COLD


c.

Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
DTC B1475/75 is not output (normal) A
DTC B1475/75 is output B



NOTICE:

If the engine keeps idling when ambient temperature is high, the compressor may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.



A

SYSTEM IS OK

B

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY