The temperature sensor of the compressor with motor assembly detects its inverter temperature.
If the temperature exceeds the maximum, the compressor with motor assembly stops compressor operation, and this DTC will be stored.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1475/75 | Temperature of the inverter is outside the specified range (temperature is too high), or there is an open or short to ground in the temperature sensor circuit. | ·
Cooling fan system ·
Refrigerant volume ·
Compressor with motor assembly ·
CAN communication system |
Wear insulated gloves and pull out the service plug grip before inspection as procedures may require disconnecting high-voltage connectors. Carry the removed service plug in your pocket to prevent other technicians from accidentally reconnecting it while you are servicing the vehicle.
Do not touch the high-voltage connectors or terminals for 10 minutes after the service plug grip is removed.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
The hybrid control system and air conditioning system output DTCs separately. Inspect DTCs following the flow chart for the hybrid control system first if any DTCs from those systems are output simultaneously.
Use the GTS to check if the CAN communication system is functioning normally.
| Result | Proceed to |
|---|---|
| CAN DTC is not output | A |
| CAN DTC is output (w/o Central Gateway ECU) | B |
| CAN DTC is output (w/ Central Gateway ECU) | C |
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
Check the operation by referring to the table below.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Control the Electric Cooling Fan | Electric cooling fan | OFF, ON | - |
Electric cooling fan operates smoothly.
OK
NG
Install a manifold gauge set (See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT(for HFC-134a(R134a))>ON-VEHICLE INSPECTION(for R-134a), See page Vehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>ON-VEHICLE INSPECTION(for R-1234yf)).
Read the manifold gauge pressure when the following conditions are established.
Prepare the vehicle according to the chart below.
| Item | Condition |
|---|---|
| Power Switch | on (READY) |
| Vehicle Doors | Fully open |
| Temperature Setting | MAX COLD |
| Blower Speed | HI |
| A/C Switch | On |
| R/F Switch | RECIRCULATION
(30 to 35°C (86 to 95°F)) |
0.15 to 0.25 MPa (1.5 to 2.5 kgf/cm2, 21.3 to 35.6 psi)
1.37 to 1.57 MPa (14 to 16 kgf/cm2, 199 to 228 psi)
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for R-134a) | B |
| NG (for R-1234yf) | C |
A
B
C
(See pageVehicle Interior>HEATING / AIR CONDITIONING>REFRIGERANT (for HFO-1234yf(R1234yf))>REPLACEMENT)
Clear the DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR).
Prepare the vehicle according to the table below.
| Item | Condition |
|---|---|
| Engine speed | Engine idling |
| Blower speed | HI |
| A/C Switch | On |
| Temperature setting | MAX COLD |
Check for DTCs (See page Vehicle Interior>HEATING / AIR CONDITIONING>AIR CONDITIONING SYSTEM>DTC CHECK / CLEAR).
| Result | Proceed to |
|---|---|
| DTC B1475/75 is not output (normal) | A |
| DTC B1475/75 is output | B |
If the engine keeps idling when ambient temperature is high, the compressor may automatically stop to protect the inverter circuit, and DTC B1475/75 may be stored.
A
B