Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM › from 2016.05
RM2070E _58 Vehicle Interior _061946 HEATING / AIR CONDITIONING _0301837 AIR CONDITIONING SYSTEM C

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM  B14A2  Driver Side Solar Sensor Short Circuit  


DESCRIPTION

E107008E55
0.583,0.063 2.26,0.313 1.677,0.25 10 false Resistance of Photodiode 0.5,0.75 0.958,1 0.458,0.25 10 false High 0.51,2.313 0.969,2.583 0.458,0.271 10 false Low 0.969,2.573 1.49,2.823 0.521,0.25 10 false Weak 2.313,2.594 2.865,2.865 0.552,0.271 10 false Strong 0.948,2.927 2.688,3.167 1.74,0.24 10 false Strength of Solar Radiation

The solar sensor (automatic light control sensor) is installed on the upper side of the instrument panel. It detects sunlight to control air conditioning AUTO mode. The output voltage from the solar sensor (automatic light control sensor) varies in accordance with the amount of sunlight. When the amount of sunlight increases, the output voltage increases. As the sunlight decreases, the output voltage decreases. The air conditioning amplifier assembly detects changes in the output voltage from the solar sensor (automatic light control sensor).

DTC No. DTC Detection Condition Trouble Area
B14A2 Short in driver side solar sensor (automatic light control sensor) circuit
·

Solar sensor (automatic light control sensor)

·

Harness or connector between solar sensor (automatic light control sensor) and air conditioning amplifier assembly

·

Harness or connector between solar sensor (automatic light control sensor) and main body ECU (multiplex network body ECU)

·

Main body ECU (multiplex network body ECU)

·

Air conditioning amplifier assembly



WIRING DIAGRAM

E220242E05
4.667,0.365 5.01,0.688 0.344,0.323 10 false 22 4.667,0.833 4.969,1.094 0.302,0.26 10 false 20 4.094,1.438 7.042,1.854 2.948,0.417 10 false Main Body ECU (Multiplex Network Body ECU) 4.094,1.281 4.469,1.542 0.375,0.26 10 false L201 4.656,2.323 4.948,2.667 0.292,0.344 10 false 33 0.365,2.969 3.229,3.24 2.865,0.271 10 false Solar Sensor (Automatic Light Control Sensor) 0.375,2.802 0.74,3.042 0.365,0.24 10 false I1 4.948,2.458 5.281,2.729 0.333,0.271 10 false TS 4.49,3.042 6.76,3.354 2.271,0.313 10 false Air Conditioning Amplifier Assembly 4.49,2.875 4.906,3.146 0.417,0.271 10 false L17 1.813,2.458 2.333,2.771 0.521,0.313 10 false NSHA 4.927,0.5 5.427,0.792 0.5,0.292 10 false CLTE 4.927,0.969 5.333,1.229 0.406,0.26 10 false CLTB 1.844,0.51 2.323,0.781 0.479,0.271 10 false CLTE 1.854,0.969 2.313,1.208 0.458,0.24 10 false CLTB 2.333,0.375 2.76,0.792 0.427,0.417 10 false 6 2.333,0.833 2.583,1.229 0.25,0.396 10 false 3 2.344,2.313 2.583,2.635 0.24,0.323 10 false 1

CAUTION / NOTICE / HINT

HINT:

If DTC B1244 is output together with other DTCs, troubleshoot DTC B1244 first (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>B1244).


PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Air Conditioner / Data List.


e.

Check the value(s) by referring to the table below.

Air Conditioner
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solar Sensor (D side) Solar sensor (automatic light control sensor) /
Min.: 0
Max.: 255
Solar sensor value increases as brightness increases -

OK:

The display is as specified in the Normal Condition column.


Result:
Result Proceed to
NG A
OK (When troubleshooting according to Problem Symptoms Table) B
OK (When troubleshooting according to the DTC) C




A

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (POWER SOURCE CIRCUIT)

B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

C

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

2.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (POWER SOURCE CIRCUIT)
a.

Disconnect the I1 solar sensor (automatic light control sensor) connector.


U155091E01
0.295,0.204 0.481,0.366 0.186,0.162 10 *a 0.407,2.558 0.829,2.721 0.422,0.162 10 CLTB 2.598,2.704 3.020,2.867 0.422,0.162 10 CLTE 1.891,2.7 2.578,2.786 false 1.452,2.464 0.868,2.636 false 1.634,0.875 1.838,1.056 0.205,0.181 10 I1

b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I1-3 (CLTB) - I1-6 (CLTE) Power switch off Below 1 V
I1-3 (CLTB) - I1-6 (CLTE) Power switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Solar Sensor (Automatic Light Control Sensor))


OK

3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) - AIR CONDITIONING AMPLIFIER)

NG

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR))
3.CHECK HARNESS AND CONNECTOR (SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR) - AIR CONDITIONING AMPLIFIER)
a.

Disconnect the L17 air conditioning amplifier assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-33 (TS) - I1-1 (NSHA) Always Below 1 Ω
L17-33 (TS) - Body ground Always 10 kΩ or higher




OK

4.INSPECT SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)
a.
U155092E02
2,1.406 2.656,0.969 false 0.885,2.375 1.542,1.938 false 0.25,0.146 0.438,0.333 0.188,0.188 10 false *a 2.708,0.875 3.135,1.063 0.427,0.188 10 false NSHA 0.531,2.406 0.917,2.594 0.385,0.188 10 false CLTE 1.729,0.385 1.979,0.594 0.25,0.208 10 false I1

Remove the solar sensor (automatic light control sensor) (See page Vehicle Interior>HEATING / AIR CONDITIONING>SOLAR SENSOR>REMOVAL).


b.

Reconnect the I1 solar sensor (automatic light control sensor) connector.


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I1-1 (NSHA) - I1-6 (CLTE) Sensor is exposed to electric light 0.8 to 4.3 V
I1-1 (NSHA) - I1-6 (CLTE) Sensor is covered with a cloth Below 0.8 V


NOTICE:
·

The connection procedure for using a digital tester such as a TOYOTA electrical tester is shown above. When using an analog tester, connect the positive (+) lead to terminal 6 and the negative (-) lead to terminal 1 of the solar sensor (automatic light control sensor).

·

While using the auxiliary battery during inspection, do not bring the positive (+) and negative (-) tester probes too close to each other as a short circuit may occur.



HINT:
·

Use an incandescent light for inspection. Bring it within about 30 cm (11.8 in.) of the solar sensor (automatic light control sensor).

·

As the inspection light is moved away from the sensor, the voltage decreases.



Text in Illustration
*a Component with harness connected
(Solar Sensor (Automatic Light Control Sensor))



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR)

5.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - SOLAR SENSOR (AUTOMATIC LIGHT CONTROL SENSOR))
a.

Disconnect the L201 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L201-20 (CLTB) - I1-3 (CLTB) Always Blow 1 Ω
L201-22 (CLTE) - I1-6 (CLTE) Always Blow 1 Ω
L201-20 (CLTB) or I1-3 (CLTB) - Body ground Always 10 kΩ or higher
L201-22 (CLTE) or I1-6 (CLTE) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR