Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM › 2012.03–2013.08
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301864 POWER WINDOW CONTROL SYSTEM J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

When the hybrid control system is running or the power switch is on (IG), the power window regulator motor assembly (for front passenger door) is operated by the power window regulator switch assembly. The power window regulator motor assembly (for front passenger door) has motor, regulator, and ECU functions.

WIRING DIAGRAM

B296639E07
1.612,0.672 3.569,0.982 1.958,0.310 10 from Main Body ECU (Multiplex Network Body ECU) 1.22,4.362 2.876,4.525 1.656,0.162 10 : LIN Communication Line 3.602,4.362 4.346,4.525 0.744,0.162 10 *2: for RHD 3.602,4.012 4.346,4.175 0.744,0.162 10 *1: for LHD 0.098,3.624 0.904,3.761 0.806,0.137 10 N7*1, O13*2 5.094,3.776 7.077,4.260 1.983,0.484 10 Power Window Regulator Motor Assembly (for Front Passenger Door) 0.1,3.776 2.782,3.933 2.682,0.158 10 Power Window Regulator Switch Assembly 5.094,3.612 5.838,3.749 0.744,0.137 10 N2*1, O2*2 5.479,0.598 5.608,0.764 0.129,0.167 10 9 5.425,1.731 5.610,1.898 0.185,0.167 10 10 1.601,1.731 1.730,1.898 0.128,0.167 10 6 1.601,2.265 1.708,2.431 0.107,0.167 10 7 5.479,2.266 5.608,2.433 0.129,0.167 10 7 5.702,0.723 6.036,0.893 0.334,0.170 10 LIN 5.702,1.828 5.918,1.967 0.216,0.138 10 UP 5.702,2.348 6.167,2.485 0.465,0.137 10 DOWN 1.266,1.82 1.476,1.961 0.210,0.141 10 UP 1.014,2.378 1.474,2.518 0.460,0.140 10 DOWN 1.601,2.831 1.730,2.998 0.128,0.167 10 1 1.137,2.946 1.475,3.084 0.338,0.138 10 GND

CAUTION / NOTICE / HINT

NOTICE:
·

The power window control system uses a LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING). Troubleshoot the power window control system after confirming that the communication system is functioning properly.

·

If the power window regulator motor assembly (for front passenger door) has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).



PROCEDURE

1.READ VALUE USING GTS (Main Body)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the Data List according to the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Communication P-Door Motor Connection status between power window regulator motor (for front passenger door) and main body ECU (multiplex network body ECU) / STOP or OK STOP: Communication stopped
OK: Normal communication
-

OK:

On the GTS screen, OK is displayed.




OK

2.READ VALUE USING GTS (P-Door Motor)

NG

GO TO LIN COMMUNICATION SYSTEM (Proceed to How to Proceed with Troubleshooting)

2.READ VALUE USING GTS (P-Door Motor)
a.

Enter the following menus: Body Electrical / P-Door Motor / Data List.


b.

Read the Data List according to the display on the GTS.

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Up SW Front passenger door power window manual up switch signal / OFF or ON OFF: Front passenger power window manual up switch not operated
ON: Front passenger door power window manual up switch operated
-
P Door P/W Down SW Front passenger door power window manual down switch signal / OFF or ON OFF: Front passenger power window manual down switch not operated
ON: Front passenger door power window manual down switch operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

3.PERFORM ACTIVE TEST USING GTS (P-Door Motor)

NG

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (P-Door Motor)
a.

Enter the following menus: Body Electrical / P-Door Motor / Active Test.


b.

Perform the Active Test according to the display on the GTS.

CAUTION:

Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.


P-Door Motor
Tester Display Test Part Control Range Diagnostic Note
Power Window Power window OFF / UP / DOWN -

OK:

Front passenger door power window operates normally.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

4.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.
B203473E30
0.623,1.607 0.776,1.750 0.153,0.144 10 *a 1.716,2.439 2.047,2.581 0.331,0.142 10 GND 0.227,3.045 0.694,3.191 0.467,0.146 10 DOWN 1.445,3.045 1.658,3.186 0.213,0.141 10 UP 1.699,2.515 1.413,2.515 false 1.201,2.785 1.201,3.128 1.201,3.128 1.416,3.128 false 1.004,2.785 1.004,3.128 1.004,3.128 0.789,3.128 false

Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 (UP) - 1 (GND) Auto up or up position Below 1 Ω
7 (DOWN) - 1 (GND) Auto down or down position Below 1 Ω


Text in Illustration
*a Component without harness connected
(Power Window Regulator Switch Assembly)



OK

5.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER DOOR SWITCH - MOTOR AND BODY GROUND)

NG

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (FRONT PASSENGER DOOR SWITCH - MOTOR AND BODY GROUND)
a.

Disconnect the N2*1 or O2*2 power window regulator motor assembly (for front passenger door) connector.

·

*1: for LHD

·

*2: for RHD



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
N7-6 (UP) - N2-10 (UP) Always Below 1 Ω
N7-7 (DOWN) - N2-7 (DOWN) Always Below 1 Ω
N7-1 (GND) - Body ground Always Below 1 Ω
N7-6 (UP) - Body ground Always 10 kΩ or higher
N7-7 (DOWN) - Body ground Always 10 kΩ or higher
N2-10 (UP) - Body ground Always 10 kΩ or higher
N2-7 (DOWN) - Body ground Always 10 kΩ or higher

for RHD
Tester Connection Condition Specified Condition
O13-6 (UP) - O2-10 (UP) Always Below 1 Ω
O13-7 (DOWN) - O2-7 (DOWN) Always Below 1 Ω
O13-1 (GND) - Body ground Always Below 1 Ω
O13-6 (UP) - Body ground Always 10 kΩ or higher
O13-7 (DOWN) - Body ground Always 10 kΩ or higher
O2-10 (UP) - Body ground Always 10 kΩ or higher
O2-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY (for Front Passenger Door)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR