85292B
1.REMOVE FRONT WIPER ARM HEAD CAP
2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH
3.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH
55810F
4.REMOVE FRONT VENTILATOR ASSEMBLY
55781E
5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY
6.DISCONNECT ROOF HEADLINING ASSEMBLY
87810
7.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)
87818
8.REMOVE INNER REAR VIEW MIRROR COVER (w/ EC Mirror)
87810
9.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)
56111
10.REMOVE WINDSHIELD GLASS (for Standard Roof)
Apply protective tape to the installation position of the windshield glass on the vehicle body.
| *1 | Protective Tape |
Apply protective tape to the installation surface to prevent it from being scratched.
Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.
| *1 | Matchmark |
Matchmarks are not necessary if the windshield glass is not going to be reused.
Pass a piano wire between the vehicle body and windshield glass from the interior as shown in the illustration.
| *1 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive applied to the bottom of the windshield glass by pulling the piano wire under the glass.
When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.
While pushing back the lip of the molding with a screwdriver, pass a piano wire between the vehicle body and windshield glass so that both wire ends are in the interior as shown in the illustration.
| *A | 1-piece Type | *B | 2-piece Type |
| *1 | Piano Wire | *2 | Adhesive |
| *3 | No. 1 Stopper | *4 | No. 2 Stopper |
| *a | Lip of the molding | - | - |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the windshield glass.
When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.
When passing the piano wire below the 2 stoppers, make sure to cut the adhesive applied between the windshield glass and stoppers.
Be careful not to drop the windshield glass.
Disconnect the windshield glass stoppers.
| *A | 1-piece Type | *B | 2-piece Type |
| *1 | No. 1 Stopper | *2 | No. 2 Stopper |
There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.
To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.
When removing the windshield glass, do not replace the windshield outside moulding with a repair moulding. Make sure to use a new one.
Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.
Using suction cups, remove the windshield glass.
Be careful not to drop the windshield glass.
Leave as much adhesive on the vehicle body as possible when removing the windshield glass.
Remove the parts of the 2 No. 1 windshield glass stoppers (1-piece type) or 2 No. 2 windshield glass stoppers (2-piece type) that remain on the vehicle.
56111
11.REMOVE WINDSHIELD GLASS (for Glass Roof)
Apply protective tape to the installation position of the windshield glass on the vehicle body.
| *1 | Protective Tape |
Apply protective tape to the installation surface to prevent it from being scratched.
Cut the windshield outside sub moulding as shown in the illustration.
| *a | Cut |
Place matchmarks on the windshield glass and vehicle body at the locations indicated in the illustration.
| *1 | Matchmark |
Matchmarks are not necessary if the windshield glass is not going to be reused.
Pass a piano wire between the vehicle body and windshield glass from the interior as shown in the illustration.
| *1 | Piano Wire |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive applied to the bottom of the windshield glass by pulling the piano wire under the glass.
When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.
While pushing back the lip of the molding with a screwdriver, pass a piano wire between the vehicle body and windshield glass so that both wire ends are in the interior as shown in the illustration.
| *A | 1-piece Type | *B | 2-piece Type |
| *1 | Piano Wire | *2 | Adhesive |
| *3 | No. 1 Stopper | *4 | No. 2 Stopper |
| *a | Lip of the molding | - | - |
Tie both wire ends to wooden blocks or similar objects that can serve as handles.
Cut off the adhesive by pulling the piano wire around the windshield glass.
When separating the windshield glass, be careful not to damage the paint or interior and exterior ornaments.
To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.
When passing the piano wire below the 2 stoppers, make sure to cut the adhesive applied between the windshield glass and stoppers.
Be careful not to drop the windshield glass.
Disconnect the windshield glass stoppers.
| *A | 1-piece Type | *B | 2-piece Type |
| *1 | No. 1 Stopper | *2 | No. 2 Stopper |
There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.
To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.
When removing the windshield glass, do not replace the windshield outside moulding with a repair moulding. Make sure to use a new one.
Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.
Using suction cups, remove the windshield glass.
Be careful not to drop the windshield glass.
Leave as much adhesive on the vehicle body as possible when removing the windshield glass.
Remove the parts of the 2 No. 1 windshield glass stoppers (1-piece type) or 2 No. 2 windshield glass stoppers (2-piece type) that remain on the vehicle.
56117A
12.REMOVE WINDOW GLASS ADHESIVE DAM
Using a scraper, remove the windshield glass adhesive dam.
| *A | Back Side |
Be careful not to damage the windshield glass.
Be sure to replace the window glass adhesive dam with a new one.
75533G
13.REMOVE WINDSHIELD OUTSIDE MOULDING (for Standard Roof)
Using a scraper, remove the windshield outside moulding.
| *A | Back Side |
Be careful not to damage the windshield glass.
Be sure to replace the windshield outside moulding with a new one.
75549A
14.REMOVE WINDSHIELD OUTSIDE SUB MOULDING (for Glass Roof)
Using a scraper, remove the windshield outside sub moulding.
| *A | Back Side |
Be careful not to damage the windshield glass.
Be sure to replace the windshield outside sub moulding with a new one.
75534
15.REMOVE WINDSHIELD OUTSIDE MOULDING LH (for Glass Roof)
Using a scraper, remove the windshield outside moulding LH.
| *A | Back Side |
Be careful not to damage the windshield glass.
Be sure to replace the windshield outside moulding LH with a new one.
75533
16.REMOVE WINDSHIELD OUTSIDE MOULDING RH (for Glass Roof)
Use the same procedure as for the LH side.
56115A
17.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)
Using a scraper, remove the 2 No. 1 windshield glass stoppers.
| *A | Back Side |
Be careful not to damage the windshield glass.
Be sure to replace the No. 1 windshield glass stoppers with new ones.
56116C
18.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Using a scraper, remove the 2 No. 2 windshield glass stoppers.
| *A | Back Side |
Be careful not to damage the windshield glass.
Be sure to replace the No. 2 windshield glass stoppers with new ones.
56115A
19.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)
Remove the 2 No. 1 windshield glass stoppers.
Be sure to replace the No. 1 windshield glass stoppers with new ones.
56111
20.CLEAN WINDSHIELD GLASS
Using a scraper, remove the adhesive tape and adhesive sticking to the windshield glass.
Be careful not to damage the windshield glass.
Clean the outer circumference of the windshield glass with a non-residue solvent.
Do not touch the windshield glass surface after cleaning it.
Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.
21.CLEAN VEHICLE BODY
Clean and shape the contact surfaces of the vehicle body.
| *1 | Adhesive |
| *2 | Body |
Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body, as shown in the illustration.
Be careful not to damage the vehicle body.
Leave as much adhesive on the vehicle body as possible.
Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.
Even if all the adhesive has been removed, clean the vehicle body.