62120B
1.CLEAN FRONT SIDE FIX WINDOW ASSEMBLY
Clean the outer edges of the front side fix window assembly with a non-residue solvent.
Do not touch the glass surface after cleaning it.
Be careful not to damage the glass or clips.
62120B
2.INSTALL FRONT SIDE FIX WINDOW ASSEMBLY
Using a brush or a sponge, apply body primer to the exposed part of the vehicle body.
| *1 | Body Primer | *2 | Brush |
| *3 | Adhesive | - | - |
| *a | CORRECT | *b | WRONG |
| *c | Edge of Curved Surface | - | - |
Do not coat the adhesive with body primer.
Do not apply too much body primer.
Allow the body primer to dry for 3 minutes or more.
Throw away any leftover body primer.
Using a brush or a sponge, apply body primer to the contact surface of the front side fix window assembly.
| *A | Back Side | - | - |
| *1 | Body Primer | *2 | Adhesive Center |
| *3 | Ceramic Notch | - | - |
| Area | Dimension |
|---|---|
| a | 12.0 mm (0.472 in.) or more |
| b | 20.4 mm (0.803 in.) or more |
If an area other than that specified is coated by accident, wipe off the body primer with a non-residue solvent before it dries.
To prevent the glass from breaking at low temperatures, ensure that no body primer adheres to the contact surface between the moulding and glass during application.
Do not apply too much body primer.
Allow the body primer to dry for 3 minutes or more.
Throw away any leftover body primer.
Apply adhesive to the front side fix window assembly.
Toyota Genuine Windshield Glass Adhesive or equivalent
Cut off the tip of the cartridge nozzle as shown in the illustration.
| Area | Dimension |
|---|---|
| a | 8.0 mm (0.315 in.) |
| d | 6.0 mm (0.236 in.) |
Load the sealer gun with the cartridge.
Apply adhesive to the front side fix window assembly as shown in the illustration.
| *A | Back Side | - | - |
| *1 | Adhesive | *2 | Adhesive Center |
| *3 | Ceramic Notch | - | - |
| Area | Dimension |
|---|---|
| a | 9.7 mm (0.382 in.) |
| b | 6.0 mm (0.236 in.) |
| c | 15.0 mm (0.591 in.) |
| d | 16.1 mm (0.634 in.) |
| e | 8.5 mm (0.335 in.) |
| f | 9.0 mm (0.354 in.) |
Install a new front side fix window assembly to the vehicle body.
Engage the 3 clips to install the front side fix window assembly.
Hold the front side fix window assembly in place securely with protective tape or equivalent until the adhesive hardens.
Allow the body primer to dry for 3 minutes or more.
Check that the clips are attached to the body correctly.
Check the clearance between the body and glass.
Lightly press the outer surface of the glass to ensure that the glass is securely fit to the vehicle body.
Press the glass with a force of 98 N (10 kgf, 22 lbf) or more.
Using a scraper, remove any excess or protruding adhesive.
Apply adhesive onto the glass rim.
Do not drive the vehicle within the time described in the table below.
| Temperature | Minimum Time prior to Driving Vehicle |
|---|---|
| 35°C (95°F) | 1 hour and 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
3.INSPECT FOR LEAK AND REPAIR
After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.
If water leaks into the cabin, allow the water to dry and add adhesive.
Remove the protective tape.
62226
4.INSTALL LOWER FRONT PILLAR GARNISH
62212
5.INSTALL FRONT PILLAR GARNISH
62312B
6.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP
for LH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>INSTALLATION)
for RH side (See page Vehicle Interior>INTERIOR PANELS / TRIM>UPPER INSTRUMENT PANEL>INSTALLATION)