Home › Vehicle Exterior › WINDOW / GLASS › ROOF WINDOW FIX GLASS
RM2070E _59 Vehicle Exterior _061949 WINDOW / GLASS _0301873 ROOF WINDOW FIX GLASS A

WINDOW / GLASS  ROOF WINDOW FIX GLASS  INSTALLATION  


PROCEDURE

Hide 63215A 1.INSTALL ROOF WINDOW UPPER MOULDING

a.

Using a brush or a sponge, apply body primer to the installation surface of the roof window upper moulding as shown in the illustration.

B276126E01
0.347,2.631 0.504,2.780 0.157,0.149 10 *1 4.478,0.435 4.594,0.584 0.116,0.149 10 A 4.966,1.79 5.303,1.939 0.337,0.149 10 A - A 4.91,0.274 5.026,0.423 0.116,0.149 10 A 0.288,2.619 0.348,2.768 0.060,0.149 10 :

Text in Illustration
*1 Body Primer - -

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than that specified is coated by accident, wipe off the body primer with isopropyl alcohol before it dries.



b.

Install a new roof window upper moulding from the rear side of the roof window glass as shown in the illustration.

B276127E01
0.817,1.468 0.974,1.617 0.157,0.149 10 *a 0.924,1.339 0.892,1.459 false 2.931,2.624 3.089,2.773 0.157,0.149 10 *a 3.038,2.495 3.006,2.615 false

Text in Illustration
*a Cut - -


c.

Cut the roof window upper moulding at the cut positions as shown in the illustration.


Hide 63251N 2.INSTALL NO. 1 ROOF WINDOW GLASS ADHESIVE DAM

a.
B274197E01
1.579,1.693 1.689,1.856 0.111,0.163 10 a

Cut the No. 1 roof window glass adhesive dam as shown in the illustration.

Standard Dimension:
Area Dimension
a 1056 to 1066 mm (3.46 to 3.50 ft.)



b.

Using a brush or a sponge, apply body primer to the installation surface of the No. 1 roof window glass adhesive dam as shown in the illustration.

B442015E01
3.979,2.698 4.198,2.698 4.198,2.698 4.198,3.042 true 3.979,2.813 4.198,2.813 true 4,2.927 4.198,2.927 true 3.531,0.479 3.75,0.479 3.75,0.479 3.75,0.771 true 3.531,0.594 3.75,0.594 true 3.552,0.698 3.75,0.698 true 2.542,1.646 2.792,1.906 0.25,0.26 10 false A 2.948,0.302 3.198,0.563 0.25,0.26 10 false b 3.667,0.781 3.917,1.042 0.25,0.26 10 false *2 3.427,3.51 3.677,3.771 0.25,0.26 10 false a 2.563,3.406 3.01,3.646 0.448,0.24 10 false A - A 0.49,4.427 0.833,4.688 0.344,0.26 10 false : *1 4.125,3.063 4.375,3.323 0.25,0.26 10 false *2 3.208,1.563 3.375,1.729 0.167,0.167 10 true A 2.104,0.219 2.354,0.479 0.25,0.26 10 false *A 2.958,0.479 3.208,0.74 0.25,0.26 10 false b 3.417,2.708 3.667,2.969 0.25,0.26 10 false b 3.438,2.896 3.688,3.156 0.25,0.26 10 false b

Text in Illustration
*A Back Side
*1 No. 1 Roof Window Glass Adhesive Dam
*2 Line

Standard Dimension:
Area Dimension
a 11 mm (0.433 in.)
b 10 mm (0.394 in.)


NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than that specified is coated by accident, wipe off the body primer with a non-residue solvent before it dries.



c.

Install the new No. 1 roof window glass adhesive dam onto the roof window glass as shown in the illustration.

B465335E01
4.167,1.917 6.5,3.333 2.333,1.417 2.083,1 2.25,0.99 true 2.313,0.781 2.583,0.781 true 2.333,0.677 2.583,0.677 2.583,0.677 2.583,0.958 true 2.667,3.125 2.917,3.125 true 2.667,3.01 2.917,3.01 true 2.667,2.906 2.917,2.906 2.917,2.906 2.917,3.25 true 2.656,2.781 2.833,2.75 true 2.313,0.896 2.583,0.896 true 0.323,0.146 0.74,0.406 0.417,0.26 10 false *A 1.729,0.51 1.917,0.74 0.188,0.229 10 false b 1.896,0.917 2.313,1.177 0.417,0.26 10 false *1 2.5,0.969 2.917,1.229 0.417,0.26 10 false *2 1.146,1.813 1.563,2.073 0.417,0.26 10 false A 4.25,1.969 4.667,2.229 0.417,0.26 10 false A - A 5.167,2.073 5.583,2.333 0.417,0.26 10 false a 1.729,0.698 1.917,0.927 0.188,0.229 10 false b 1.865,1.719 2.01,1.917 0.146,0.198 10 true A 2.885,2.656 3.302,2.917 0.417,0.26 10 false *1 2.844,3.26 3.26,3.521 0.417,0.26 10 false *2 2.073,2.917 2.26,3.146 0.188,0.229 10 false b 2.083,3.094 2.271,3.323 0.188,0.229 10 false b

Text in Illustration
*A Back Side
*1 No. 1 Roof Window Glass Adhesive Dam
*2 Line

Standard Dimension:
Area Dimension
a 5.0 to 8.0mm (0.197 to 0.315 in.)
b 10 mm (0.394 in.)



Hide 63212A 3.INSTALL ROOF WINDOW GLASS

a.

Pass a string under the windshield outside sub moulding as shown in the illustration.

B276125E03
5.156,3.302 4.854,3.302 false 5.26,0.729 5.563,0.552 false 5.594,0.469 5.75,0.615 0.156,0.146 10 false *2 4.698,3.229 4.854,3.375 0.156,0.146 10 false *1

Text in Illustration
*1 String *2 Windshield Outside Sub Moulding


b.

Using a brush or a sponge, apply body primer to the exposed part of the vehicle body.

B283215E01
1.358,0.367 1.515,0.516 0.157,0.149 10 *2 2.888,1.343 3.045,1.492 0.157,0.149 10 *3 5.229,0.504 5.386,0.653 0.157,0.149 10 *4 0.325,4.578 0.482,4.726 0.157,0.149 10 *1 2.793,0.258 2.950,0.407 0.157,0.149 10 *b 1.784,0.258 1.941,0.407 0.157,0.149 10 *a 2.462,2.167 2.591,2.316 0.130,0.149 10 C 4.146,2.721 4.276,2.870 0.130,0.149 10 D 4.566,2.721 4.696,2.870 0.130,0.149 10 D 1.007,3.336 1.122,3.485 0.116,0.149 10 A 5.833,0.35 6.170,0.499 0.337,0.149 10 B - B 5.833,1.813 6.175,1.962 0.342,0.149 10 C - C 5.833,3.276 6.175,3.425 0.342,0.149 10 D - D 4.149,0.364 4.486,0.513 0.337,0.149 10 A - A 1.651,3.336 1.767,3.485 0.116,0.149 10 A 1.047,2.519 1.162,2.668 0.116,0.149 10 B 1.687,2.519 1.803,2.668 0.116,0.149 10 B 2.457,1.637 2.586,1.786 0.130,0.149 10 C 1.053,0.594 1.343,0.437 false 2.966,1.333 3.06,1.147 false 5.127,0.755 5.221,0.569 false 6.821,0.614 6.979,0.763 0.157,0.149 10 *4 6.715,0.861 6.809,0.675 false 6.462,2.298 6.619,2.447 0.157,0.149 10 *4 6.382,2.601 6.449,2.369 false 5.862,3.597 6.020,3.746 0.157,0.149 10 *4 6.1,3.834 6.012,3.662 false 6.366,3.633 6.524,3.782 0.157,0.149 10 *4 6.604,3.87 6.516,3.698 false

Text in Illustration
*1 Body Primer *2 Brush
*3 Adhesive *4 Edge of Curved Surface
*a CORRECT *b WRONG

NOTICE:
·

Do not coat the adhesive with body primer.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.




c.

Using a brush or a sponge, apply body primer to the contact surface of the roof window glass.

B276131E02
2.083,3.146 2.083,3.344 false 3.021,3.104 3.021,3.292 true 2.073,0.458 1.719,0.219 false 1.573,4.115 1.323,4.26 false 3.927,4.156 3.688,4.302 false 6.531,4.115 6.292,4.26 false 5.698,4.115 5.938,4.26 false 1.635,5.479 1.396,5.625 false 3.677,5.802 3.802,5.99 false 2.01,3.354 2.167,3.5 0.156,0.146 10 false *2 0.146,0.135 0.344,0.302 0.198,0.167 10 false *A 2.177,2.448 2.292,2.594 0.115,0.146 10 true B 1.594,2.448 1.708,2.594 0.115,0.146 10 false B 2.281,2.854 2.406,3 0.125,0.146 10 true C 1.677,2.854 1.802,3 0.125,0.146 10 false C 3.698,2.688 3.823,2.833 0.125,0.146 10 false D 3.698,3.323 3.823,3.469 0.125,0.146 10 false D 2.146,1.542 2.26,1.688 0.115,0.146 10 true A 1.563,1.542 1.677,1.688 0.115,0.146 10 false A 2.677,3.677 3.01,3.823 0.333,0.146 10 false B - B 0.427,3.677 0.76,3.823 0.333,0.146 10 false A - A 0.5,6.563 0.656,6.708 0.156,0.146 10 false *1 0.427,6.552 0.49,6.698 0.063,0.146 10 false : 5.125,1.417 5.25,1.563 0.125,0.146 10 false E 5.521,1.417 5.646,1.563 0.125,0.146 10 false E 4.927,3.677 5.271,3.823 0.344,0.146 10 false C - C 2.667,5.146 3.01,5.292 0.344,0.146 10 false E - E 0.417,5.146 0.76,5.292 0.344,0.146 10 false D - D 2.958,3.302 3.115,3.448 0.156,0.146 10 false *2 1.563,0.146 1.719,0.292 0.156,0.146 10 false *2 1.583,4.052 1.74,4.198 0.156,0.146 10 false *2 3.938,4.083 4.094,4.229 0.156,0.146 10 false *2 6.542,4.052 6.698,4.198 0.156,0.146 10 false *2 5.542,4.052 5.698,4.198 0.156,0.146 10 false *2 1.646,5.417 1.802,5.563 0.156,0.146 10 false *2 3.531,5.729 3.688,5.875 0.156,0.146 10 true *2

Text in Illustration
*A Back Side - -
*1 Body Primer *2 Line

CAUTION:

Make sure to use body primer to install the roof window glass made of resin. Failure to do so may cause it to come off.


NOTICE:
·

To prevent the glass from breaking at low temperatures, ensure that no body primer adheres to the contact surface between the moulding and glass during application.

·

Do not apply too much body primer.

·

Allow the body primer to dry for 3 minutes or more.

·

Throw away any leftover body primer.



HINT:

If an area other than that specified is coated by accident, wipe off the body primer with a non-residue solvent before it dries.



d.

Apply adhesive to the roof window glass.

Adhesive:

Toyota Genuine Windshield Glass Adhesive or equivalent


i.
B214800E01
0.496,0.546 0.650,0.739 0.154,0.193 10 a 1.339,1.361 1.494,1.554 0.154,0.193 10 a 1.142,0.852 1.296,1.045 0.154,0.193 10 b 0.75,0.937 0.905,1.130 0.154,0.193 10 b

Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard Dimension:
Area Dimension
a 12 mm (0.472 in.)
b 8.0 mm (0.315 in.)



ii.

Load the sealer gun with cartridge.


iii.

Apply adhesive to the roof window glass as shown in the illustration.

B276132E02
2.198,3.167 2.198,3.354 false 1.573,4.313 1.333,4.458 false 3.885,4.448 3.646,4.594 false 6.656,4.323 6.417,4.469 false 5.823,4.323 6.063,4.469 false 1.531,5.479 1.281,5.625 false 3.688,5.781 3.813,5.969 false 2.125,3.354 2.281,3.5 0.156,0.146 10 false *2 0.146,0.135 0.344,0.302 0.198,0.167 10 false *A 2.177,2.448 2.292,2.594 0.115,0.146 10 true B 1.594,2.448 1.708,2.594 0.115,0.146 10 false B 2.281,2.854 2.406,3 0.125,0.146 10 true C 1.677,2.854 1.802,3 0.125,0.146 10 false C 3.698,2.719 3.823,2.865 0.125,0.146 10 false D 3.698,3.302 3.823,3.448 0.125,0.146 10 false D 2.146,1.542 2.26,1.688 0.115,0.146 10 true A 1.563,1.542 1.677,1.688 0.115,0.146 10 false A 2.677,3.677 3.01,3.823 0.333,0.146 10 false B - B 0.427,3.677 0.76,3.823 0.333,0.146 10 false A - A 0.406,6.542 0.563,6.688 0.156,0.146 10 false *1 0.333,6.531 0.396,6.677 0.063,0.146 10 false : 5.125,1.417 5.25,1.563 0.125,0.146 10 false E 5.521,1.417 5.646,1.563 0.125,0.146 10 false E 4.927,3.677 5.271,3.823 0.344,0.146 10 false C - C 2.667,5.146 3.01,5.292 0.344,0.146 10 false E - E 0.417,5.146 0.76,5.292 0.344,0.146 10 false D - D 1.594,4.24 1.75,4.385 0.156,0.146 10 false *3 3.896,4.375 4.052,4.521 0.156,0.146 10 false *3 6.667,4.25 6.823,4.396 0.156,0.146 10 false *3 5.667,4.26 5.823,4.406 0.156,0.146 10 false *3 1.542,5.417 1.698,5.563 0.156,0.146 10 false *3 3.531,5.708 3.688,5.854 0.156,0.146 10 true *3 1.021,3.833 1.125,3.979 0.104,0.146 10 false a 2.969,4.073 3.073,4.219 0.104,0.146 10 false a 3.302,3.844 3.406,3.99 0.104,0.146 10 false b 6.104,3.906 6.208,4.052 0.104,0.146 10 false c 1.74,5.646 1.844,5.792 0.104,0.146 10 false c 3.896,5.396 4,5.542 0.104,0.146 10 false c

Text in Illustration
*A Back Side - -
*1 Adhesive *2 Adhesive Center
*3 Line - -

Standard Dimension:
Area Dimension
a 4.0 mm (0.157 in.)
b 8.0 mm (0.315 in.)
c 11.0 mm (0.433 in.)




e.

Install the roof window glass.

i.

Using suction cups, engage the 2 pins and 4 clips to install the roof window glass.


ii.

Lightly press the front surface of the roof window glass to ensure that the roof window glass is securely fit to the roof panel reinforcement.

HINT:

Press the roof window glass with a force of 98 N (10 kgf, 22 lbf) or more.



iii.

Apply soapy water to the windshield outside sub moulding.


iv.

Slowly pull out the string to install the windshield outside sub moulding to the correct position.


v.

Hold the roof window glass using protective tape until applied adhesive becomes hard.

NOTICE:

Do not drive the vehicle within the time described in the table below.


Minimum Time:
Temperature Minimum Time prior to Driving Vehicle
35°C (95°F) 1 hour and 30 minutes
20°C (68°F) 5 hours
5°C (41°F) 24 hours




Hide 63250H 4.INSTALL SUNSHADE HOUSING ASSEMBLY