Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2. REPAIR INSTRUCTION
75922M
3.INSTALL NO. 1 BLACK OUT TAPE
75976G
4.INSTALL FRONT DOOR LOWER OUTSIDE STRIPE
75966B
5.INSTALL FRONT DOOR REAR OUTSIDE STRIPE
75986B
6.INSTALL FRONT DOOR STRIPE
75756C
7.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING
75720
8.INSTALL FRONT DOOR BELT MOULDING ASSEMBLY
67001A
9.INSTALL FRONT DOOR PANEL CUSHION
Engage the 2 claws to install 2 new front door panel cushions.
67862
10.INSTALL FRONT DOOR WEATHERSTRIP
Engage the 17 clips and install the front door weatherstrip.
68620
11.INSTALL FRONT DOOR CHECK ASSEMBLY
Apply MP grease to the sliding areas of the front door check assembly.
Apply adhesive to the threads of the bolt (A).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the front door check assembly with the 3 bolts.
67664C
12.INSTALL DOOR FRAME GARNISH
Engage the clip to install a new door frame garnish.
69312
13.INSTALL FRONT DOOR LOCK OPEN ROD
Install the front door lock open rod as indicated by the arrows, in the order shown in the illustration.
82152A
14.INSTALL FRONT DOOR WIRE (w/ Entry and Start System)
Engage the 2 clamps to install the front door wire.
69202A
15.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts on the front door outside handle frame sub-assembly.
Engage the door handle nut and claw.
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly with the screw.
w/ Entry and Start System:
Engage the clamp.
Connect the connector.
69760C
16.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
Install the front door inside locking cable assembly as shown in the illustration.
69760C
17.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
Install the front door inside locking cable assembly as shown in the illustration.
Engage the 3 claws as shown in the illustration.
69720B
18.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
Install the front door lock remote control cable assembly as shown in the illustration.
69720B
19.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
Install the front door lock remote control cable assembly as shown in the illustration.
69036A
20.INSTALL FRONT DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)
Engage the 2 claws.
Engage the 2 claws to install the front door lock cover sub-assembly as shown in the illustration.
69320
21.INSTALL FRONT DOOR LOCK ASSEMBLY
When reusing a removed front door lock assembly, replace the door lock wiring harness seal with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the front door lock assembly.
Apply MP grease to the sliding parts of the front door lock assembly.
When reusing the front door lock assembly:
Install a new door lock wiring harness seal to the front door lock assembly.
Connect the front door lock open rod to the front door lock assembly.
| *1 | Front Door Lock Open Rod |
Make sure that the front door lock open rod is securely connected to the front door lock assembly.
Using a T30 "TORX" socket wrench, install the front door lock assembly with the 3 screws.
Connect the connector.
69242E
22.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD
Engage the 2 claws to install the front door rear outside handle pad.
69241H
23.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD
Engage the 3 claws to install the front door front outside handle pad.
69220
24.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY
Insert the front end of the front door outside handle assembly into the front door outside handle frame.
Insert the rear end of the front door outside handle assembly into the front door outside handle frame, then slide the front door outside handle assembly toward the front of the vehicle to install it.
Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.
w/ Entry and Start System:
Connect the connector.
Engage the 2 claws.
69217D
25.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Driver Side)
Engage the 2 guides and claw to install the front door outside handle cover to the front door lock cylinder.
69217D
26.INSTALL FRONT DOOR OUTSIDE HANDLE COVER (for Front Passenger Side)
Using a T30 "TORX" socket wrench, install the front door outside handle cover with the screw.
Install the hole plug.
27.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Install the front door outside handle cover with lock cylinder assembly.
Make sure that the front door lock cylinder rod is inserted into the front door lock assembly.
Using a T30 "TORX" socket wrench, install the front door lock cylinder with the screw.
Install the hole plug.
67404F
28.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY
Engage the guide as shown in the illustration.
Install the front door rear lower frame sub-assembly with the bolt.
68151D
29.INSTALL FRONT DOOR GLASS RUN
Install the front door glass run.
85720D
30.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
The regulator arm must be below the intermediate position when installing the power window regulator motor.
Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
31.INSTALL FRONT DOOR POWER WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the front door power window regulator assembly.
Install the temporary bolt to the front door power window regulator assembly.
Temporarily install the front door power window regulator assembly.
| *1 | Temporary Bolt |
Tighten the temporary bolt and 5 bolts.
Connect the connector.
68102
32.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the multiplex network master switch assembly and move the front door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) auxiliary battery terminal and multiplex network master switch assembly.
Insert the front door glass sub-assembly into the front door panel along the front door glass run as indicated by the arrows, in the order shown in the illustration.
Install the front door glass sub-assembly with the 2 bolts.
Install the grommet.
67832
33.INSTALL FRONT DOOR SERVICE HOLE COVER
Apply new butyl tape to the front door panel.
Pass the front door lock remote control cable assembly and front door inside locking cable assembly through a new front door service hole cover.
Attach the front door service hole cover according to the reference points on the front door panel.
| *1 | Reference Point |
Securely install the front door service hole cover preventing wrinkles and air bubbles.
67626
34.INSTALL FRONT DOOR TRIM BRACKET
Install the front door trim bracket with the 2 screws.
86160
35.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY
36.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY WITH COVER
87964
37.INSTALL OUTER MIRROR INSTALL HOLE COVER
87912A
38.INSTALL OUTER MIRROR PROTECTOR
81230
39.INSTALL COURTESY LIGHT ASSEMBLY
69206B
40.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 2 claws to install the front door inside handle sub-assembly to the front door trim board sub-assembly.
68172A
41.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP
Engage the 7 claws to install the front door inner glass weatherstrip to the front door trim board sub-assembly as shown in the illustration.
67602
42.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY
Connect the front door lock remote control cable assembly and front door inside locking cable assembly to the front door inside handle.
| *1 | Front Door Inside Locking Cable Assembly |
| *2 | Front Door Lock Remote Control Cable Assembly |
Connect the courtesy light connector.
Engage the 9 clips and install the front door trim board sub-assembly.
Install the 2 screws.
If protective tape has been applied, remove it.
74222
43.INSTALL DOOR ARMREST COVER
Install the door armrest cover.
44.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Connect the connector.
Engage the 4 guides, 11 claws and clip to install the multiplex network master switch assembly with front door armrest base panel.
45.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Connect the connector.
Engage the 4 guides, 11 claws and clip to install the power window regulator switch assembly with front door armrest base panel.
69284C
46.INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG
Engage the 3 claws to install the front door inside handle bezel plug.
47.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
64995
48.INSTALL DECK FLOOR BOX RH
64993
49.INSTALL REAR DECK FLOOR BOX
58411A
50.INSTALL NO. 1 DECK BOARD
58412A
51.INSTALL NO. 2 DECK BOARD
58410B
52.INSTALL DECK BOARD ASSEMBLY
53.INITIALIZE POWER WINDOW CONTROL SYSTEM
54.INSPECT POWER WINDOW OPERATION