Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
2. REPAIR INSTRUCTION
75924
3.INSTALL NO. 2 BLACK OUT TAPE
75978H
4.INSTALL REAR DOOR LOWER OUTSIDE STRIPE
75989C
5.INSTALL REAR DOOR UPPER OUTSIDE STRIPE
75988C
6.INSTALL REAR DOOR OUTSIDE STRIPE
75762A
7.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING
75740
8.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
67674A
9.INSTALL REAR DOOR FRAME GARNISH (w/o Rear Door Sunshade)
Engage the clip to install a new rear door frame garnish.
67676C
10.INSTALL REAR DOOR NO. 2 FRAME GARNISH (w/o Rear Door Sunshade)
Engage the clip to install a new rear door No. 2 frame garnish.
67674A
11.INSTALL REAR DOOR FRAME GARNISH (w/ Rear Door Sunshade)
Engage the clip to install a new rear door frame garnish.
67676C
12.INSTALL REAR DOOR NO. 2 FRAME GARNISH (w/ Rear Door Sunshade)
Engage the clip to install a new rear door No. 2 frame garnish.
67837C
13.INSTALL REAR DOOR DUST PROOF SEAL
Engage the claw to install a new rear door dust proof seal as shown in the illustration.
Install the rear door dust proof seal with the arrow facing up.
Use the same procedure for the other rear door dust proof seal.
67003C
14.INSTALL REAR DOOR PANEL CUSHION
Engage the 2 claws to install 2 new rear door panel cushions.
69204A
15.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY
Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.
Engage the door handle nut and claw.
| *a | Outside |
| *b | Inside |
Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.
69242G
16.INSTALL REAR DOOR REAR OUTSIDE HANDLE PAD
Engage the 2 claws to install the rear door rear outside handle pad.
69241G
17.INSTALL REAR DOOR FRONT OUTSIDE HANDLE PAD
Engage the 3 claws to install the rear door front outside handle pad.
69240
18.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY
Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.
If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.
Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.
Move the lever back in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.
69227L
19.INSTALL REAR DOOR OUTSIDE HANDLE COVER
Engage the claw and install the rear door outside handle cover.
Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.
69780B
20.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)
Install the rear door inside locking cable assembly as shown in the illustration.
69780B
21.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)
Install the rear door inside locking cable assembly as shown in the illustration.
Engage the 3 claws as shown in the illustration.
69740D
22.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)
Install the rear door lock remote control cable assembly as shown in the illustration.
69740D
23.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)
Install the rear door lock remote control cable assembly as shown in the illustration.
Engage the claw as shown in the illustration.
69038A
24.INSTALL REAR DOOR LOCK COVER SUB-ASSEMBLY (w/o Double Locking System)
Engage the 2 claws.
Engage the 2 claws to install the rear door lock cover sub-assembly as shown in the illustration.
69060A
25.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY
When reusing a removed rear door lock with motor assembly, replace the door lock wiring harness seal with a new one.
Do not allow grease or dust to adhere to the door lock wiring harness seal installation surface.
Reusing a door lock wiring harness seal or using a damaged door lock wiring harness seal may cause water ingress. This may result in a malfunction of the rear door lock with motor assembly.
Apply MP grease to the sliding parts of the rear door lock with motor assembly.
When reusing the rear door lock with motor assembly:
Install a new door lock wiring harness seal to the rear door lock with motor assembly.
Connect the rear door lock with motor assembly to the release plate of the rear door outside handle frame sub-assembly, and set it to the rear door panel.
| *a | Release Plate |
Make sure that the release plate of the rear door outside handle frame sub-assembly is securely connected to the rear door lock with motor assembly.
Using a T30 "TORX" socket wrench, install the rear door lock with motor assembly with the 3 screws.
85720E
26.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY
The regulator arm must be below the intermediate position when installing the rear power window regulator motor assembly.
Using a T25 "TORX" socket wrench, install the power window regulator motor assembly with the 3 screws.
A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.
27.INSTALL REAR DOOR POWER WINDOW REGULATOR ASSEMBLY
Apply MP grease to the sliding parts of the rear door power window regulator assembly.
Install the temporary bolt to the rear door power window regulator assembly.
Temporarily install rear door power window regulator assembly.
| *1 | Temporary Bolt |
Tighten the temporary bolt and 5 bolts.
68104
28.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
Connect the cable to the negative (-) auxiliary battery terminal.
Connect the rear power window regulator motor connector and power window regulator switch assembly, and move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator switch assembly and rear power window regulator motor connector.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as shown in the illustration.
Install the rear door glass sub-assembly with the 2 bolts.
67488C
29.INSTALL REAR DOOR REAR GUIDE SEAL
Install the rear door rear guide seal as shown in the illustration.
Install the 3 screws.
67408D
30.INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY
Install the rear door window guide sub-assembly with the screw and bolt.
68152C
31.INSTALL REAR DOOR GLASS RUN
Install the rear door glass run.
67872
32.INSTALL REAR DOOR WEATHERSTRIP
Engage the 20 clips and install the rear door weatherstrip.
68640A
33.INSTALL REAR DOOR CHECK ASSEMBLY
Apply MP grease to the sliding areas of the rear door check assembly.
Apply adhesive to the threads of the bolt (A).
Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
Install the rear door check assembly with the bolt and 2 nuts.
67842E
34.INSTALL REAR DOOR SERVICE HOLE COVER
Apply butyl tape to the rear door panel.
Pass the rear door lock remote control cable, rear door inside locking cable and each connector through a new rear door service hole cover.
Attach the rear door service hole cover according to the reference points on the rear door panel.
| *1 | Reference Point |
Securely install the rear door service hole cover preventing wrinkles and air bubbles.
Connect the 2 connectors.
67628
35.INSTALL REAR DOOR TRIM BRACKET
Install the rear door trim bracket with the 2 screws.
86160B
36.INSTALL REAR SPEAKER ASSEMBLY
86160Y
37.INSTALL REAR NO. 2 SPEAKER ASSEMBLY (for 8 Speakers)
69206C
38.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY
Engage the 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.
65908D
39.INSTALL REAR CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)
Install the rear curtain sub-assembly with the 9 screws.
68174A
40.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP
Engage the 7 claws to install the rear door inner glass weatherstrip to the rear door trim board sub-assembly as shown in the illustration.
67604
41.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly to the rear door inside handle sub-assembly.
| *1 | Rear Door Inside Locking Cable Assembly |
| *2 | Rear Door Lock Remote Control Cable Assembly |
for 8 Speakers:
Connect the connector.
Engage the 9 clips and install the rear door trim board sub-assembly.
Install the 2 screws.
If protective tape has been applied, remove it.
74262
42.INSTALL REAR DOOR ARMREST COVER
Install the rear door armrest cover.
43.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
Connect the connector.
Engage the 5 guides, 10 claws and clip to install the rear power window regulator switch assembly with rear door armrest base panel.
69284D
44.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
Engage the 3 claws to install the rear door inside handle bezel plug.
45.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
64995
46.INSTALL DECK FLOOR BOX RH
64993
47.INSTALL REAR DECK FLOOR BOX
58411A
48.INSTALL NO. 1 DECK BOARD
58412A
49.INSTALL NO. 2 DECK BOARD
58410B
50.INSTALL DECK BOARD ASSEMBLY
51.INITIALIZE POWER WINDOW CONTROL SYSTEM
52.INSPECT POWER WINDOW OPERATION