Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › from 2014.11
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301891 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Rain Sensor Circuit  


DESCRIPTION

The windshield wiper relay assembly receives a signal from the rain sensor to control the auto wiper system.

WIRING DIAGRAM

E226326E13
4.938,2.583 5.375,2.76 0.438,0.177 10 false L146 4.938,2.75 7.073,2.938 2.135,0.188 10 false Windshield Wiper Relay Assembly 2.885,2.656 3.25,2.833 0.365,0.177 10 false U12 2.885,2.823 3.708,3.01 0.823,0.188 10 false Rain Sensor 3.792,1.313 3.99,1.479 0.198,0.167 10 false 1 2.969,2.052 3.219,2.219 0.25,0.167 10 false ES 3.365,1.469 3.688,1.635 0.323,0.167 10 false MPX 2.958,0.917 3.26,1.083 0.302,0.167 10 false SIG 0.281,0.906 1.25,1.281 0.969,0.375 10 false from IG1 NO. 1 Relay 1.854,1.052 2.896,1.24 1.042,0.188 10 false ECU-IG NO. 2 5.396,1.469 5.875,1.635 0.479,0.167 10 false MPX1 5.125,1.323 5.323,1.49 0.198,0.167 10 false 14 2.771,0.781 2.906,0.948 0.135,0.167 10 false 4 2.771,1.938 2.906,2.104 0.135,0.167 10 false 2 0.896,3.271 2.521,3.458 1.625,0.188 10 false : Lin Communication Line

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER RELAY ASSEMBLY - RAIN SENSOR)
a.

Disconnect the L146 windshield wiper relay assembly connector.


b.

Disconnect the U12 rain sensor connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L146-14 (MPX1) - U12-1 (MPX) Always Below 1 Ω
U12-1 (MPX) - Body ground Always 10 kΩ or higher




OK

2.INSPECT HARNESS AND CONNECTOR (RAIN SENSOR - AUXILIARY BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT HARNESS AND CONNECTOR (RAIN SENSOR - AUXILIARY BATTERY AND BODY GROUND)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
U12-4 (SIG) - U12-2 (ES) Power switch on (IG) 11 to 14 V



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
U12-2 (ES) - Body ground Always Below 1 Ω




OK

3.INSPECT RAIN SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT RAIN SENSOR
a.
U191222E01
0.317,0.234 0.549,0.422 0.232,0.188 10 *a 2.195,1.37 2.629,1.522 0.434,0.152 10 MPX 1.539,1.224 1.807,1.376 0.268,0.152 10 ES 1.976,1.981 2.29,1.564 false 1.692,1.417 1.809,1.981 false 0.649,1.66 0.943,1.811 0.293,0.152 10 U12

Reconnect the U12 rain sensor connector.


b.

Connect an oscilloscope to the rain sensor connector.


c.

Check for pulses.

OK:
Tester Connection Condition Specified Condition
U12-1 (MPX) - U12-2 (ES) Power switch on (IG) Pulse generation


Text in Illustration
*a Component with harness connected
(Rain Sensor)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG