Home › Vehicle Exterior › WIPER / WASHER › WIPER AND WASHER SYSTEM › 2012.03–2014.11
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301891 WIPER AND WASHER SYSTEM J

WIPER / WASHER  WIPER AND WASHER SYSTEM  Front Wiper Motor Circuit  


DESCRIPTION

The windshield wiper relay assembly controls the windshield wiper motor assembly.

WIRING DIAGRAM

E227682E17
0.521,4.677 0.896,4.833 0.375,0.156 10 false A35 0.531,4.833 2.729,5.021 2.198,0.188 10 false Windshield Wiper Motor Assembly 5.708,4.656 6.073,4.813 0.365,0.156 10 false L146 5.708,4.813 6.823,5.354 1.115,0.542 10 false Windshield Wiper Relay Assembly 3.365,0.938 3.969,1.104 0.604,0.167 10 false WIP 4.313,0.781 5.76,0.979 1.448,0.198 10 false from IG1 NO. 2 Relay 5.823,2.771 6.344,3.125 0.521,0.354 10 false +2 2.469,2.667 2.854,2.927 0.385,0.26 10 false +2 4.354,1.458 4.698,1.667 0.344,0.208 10 false +1 2.479,1.344 2.729,1.542 0.25,0.198 10 false +1 5.823,3.552 6.458,3.906 0.635,0.354 10 false +SM 5.646,3.438 5.781,3.615 0.135,0.177 10 false 1 2.74,0.51 3.01,0.896 0.271,0.385 10 false 3*1 1*2 5.583,2.656 5.792,2.833 0.208,0.177 10 false 11 2.75,2.5 3,2.917 0.25,0.417 10 false 4*1 5*2 2.448,3.458 2.76,3.698 0.313,0.24 10 false +S 2.531,4.135 2.75,4.333 0.219,0.198 10 false E 2.542,0.677 2.698,0.854 0.156,0.177 10 false B 2.75,4.135 3.01,4.354 0.26,0.219 10 false 2 2.74,1.177 2.99,1.583 0.25,0.406 10 false 1*1 3*2 2.75,3.292 3,3.698 0.25,0.406 10 false 5*1 4*2 3.896,2.208 4.167,2.365 0.271,0.156 10 false L48 4.198,2.219 5.365,2.74 1.167,0.521 10 false Windshield Wiper Switch Assembly 4.167,1.375 4.417,1.521 0.25,0.146 10 false 3 4.333,1.854 4.729,2.115 0.396,0.26 10 false +2 4.156,1.771 4.406,1.917 0.25,0.146 10 false 4 0.552,5.354 2,5.823 1.448,0.469 10 false *1: for LHD 1.5,5.354 2.948,5.823 1.448,0.469 10 false *2: for RHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
a.
E144461E68
1.863,2.513 2.224,2.874 false 0.856,1.582 0.978,1.731 0.122,0.149 10 E 2.21,2.893 2.435,3.042 0.225,0.149 10 +2 0.374,0.372 0.578,0.521 0.205,0.149 10 *a 2.54,1.869 2.765,2.018 0.225,0.149 10 +1 2.044,2.142 2.488,1.982 false 1.733,2.05 0.991,1.666 false

for LHD:

i.

Remove the windshield wiper motor assembly (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


ii.

Check the LO operation.

Connect a auxiliary battery positive (+) lead to terminal 1 (+1) and a negative (-) lead to terminal 2 (E), and check that the motor operates at low speed.

OK:

Motor operates at low speed (LO).



iii.

Check the HI operation.

Connect a auxiliary battery positive (+) lead to terminal 4 (+2) and a negative (-) lead to terminal 2 (E), and check that the motor operates at high speed.

OK:

Motor operates at high speed (HI).


Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor Assembly)



b.
E144461E82
2.005,1.539 1.752,2.051 false 1.546,2.513 1.236,2.772 false 1.08,1.326 1.302,1.475 0.222,0.149 10 +1 1.073,2.784 1.277,2.933 0.205,0.149 10 +2 2.025,1.334 2.167,1.483 0.142,0.149 10 E 0.347,0.3 0.569,0.449 0.222,0.149 10 *a 1.249,1.563 1.503,2.074 false

for RHD:

i.

Remove the windshield wiper motor assembly (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


ii.

Check the LO operation.

Connect an auxiliary battery positive (+) lead to terminal 3 (+1) and a negative (-) lead to terminal 2 (E), and check that the motor operates at low speed.

OK:

Motor operates at low speed (LO).



iii.

Check the HI operation.

Connect an auxiliary battery positive (+) lead to terminal 5 (+2) and a negative (-) lead to terminal 2 (E), and check that the motor operates at high speed.

OK:

Motor operates at high speed (HI).


Text in Illustration
*a Component without harness connected
(Windshield Wiper Motor Assembly)




OK

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - IG1 NO. 2 RELAY AND BODY GROUND)

NG

REPLACE WINDSHIELD WIPER MOTOR ASSEMBLY

2.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - IG1 NO. 2 RELAY AND BODY GROUND)
a.

for LHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-3 (B) - Body ground Power switch on (IG) 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-2 (E) - Body ground Always Below 1 Ω




b.

for RHD:

i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A35-1 (B) - Body ground Power switch on (IG) 11 to 14 V



ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-2 (E) - Body ground Always Below 1 Ω





OK

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (WINDSHIELD WIPER MOTOR ASSEMBLY - WINDSHIELD WIPER RELAY ASSEMBLY)
a.

for LHD:

i.

Disconnect the L146 windshield wiper relay assembly connector and L48 windshield wiper switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-1 (+1) - L48-3 (+1) Always Below 1 Ω
A35-1 (+1) - Body ground Always 10 kΩ or higher
A35-4 (+2) - L146-11 (+2) Always Below 1 Ω
A35-4 (+2) - L48-4 (+2) Always Below 1 Ω
A35-4 (+2) - Body ground Always 10 kΩ or higher
A35-5 (+S) - L146-1 (+SM) Always Below 1 Ω
A35-5 (+S) - Body ground Always 10 kΩ or higher




b.

for RHD:

i.

Disconnect the L146 windshield wiper relay assembly connector and L48 windshield wiper switch assembly connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A35-3 (+1) - L48-3 (+1) Always Below 1 Ω
A35-3 (+1) - Body ground Always 10 kΩ or higher
A35-5 (+2) - L146-11 (+2) Always Below 1 Ω
A35-5 (+2) - L48-4 (+2) Always Below 1 Ω
A35-5 (+2) - Body ground Always 10 kΩ or higher
A35-4 (+S) - L146-1 (+SM) Always Below 1 Ω
A35-4 (+S) - Body ground Always 10 kΩ or higher





OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR