Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER MOTOR
RM2070E _59 Vehicle Exterior _061952 WIPER / WASHER _0301893 REAR WIPER MOTOR A

WIPER / WASHER  REAR WIPER MOTOR  INSTALLATION  


PROCEDURE

Hide 85110R 1.INSTALL REAR WIPER MOTOR ASSEMBLY

a.
E223605

Install the rear wiper motor assembly with the 3 bolts.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)


b.

Connect the connector.


Hide 85143R 2.INSTALL REAR WIPER MOTOR GROMMET

a.
E223606E01
1.48,0.676 1.741,0.936 false 2.183,0.686 1.918,0.941 false 1.746,0.937 1.915,1.087 0.169,0.150 10 *1

Apply MP grease to the entire surface of the rear wiper motor grommet lip.

Text in Illustration
*1 MP grease

HINT:

Make sure that the hole does not get clogged with grease and the grooves on the lip are filled with grease.



b.
E223607E02
2.323,0.188 2.604,0.188 false 2.656,0.104 2.906,0.333 0.25,0.229 10 false *a

Install the rear wiper motor grommet.

Text in Illustration
*a Alignment Mark

HINT:

Install the grommet with its alignment mark facing up.



Hide 3.INSTALL REAR WIPER ARM AND BLADE ASSEMBLY

a.

Operate the wiper and stop the rear wiper motor at the automatic stop position.


b.

When reusing the rear wiper arm and blade assembly:

i.
E223617E01
2.632,1.469 1.87,1.849 false 1.678,1.765 1.845,1.932 0.167,0.167 10 *1

Clean the wiper arm serrations.

Text in Illustration
*1 Wiper Arm Serration



c.

When reusing the rear wiper motor assembly:

i.
E224629E01
2.009,0.887 2.589,0.887 false 2.618,0.79 2.784,0.959 0.166,0.169 10 *1

Clean the wiper pivot serrations with a wire brush.

Text in Illustration
*1 Wiper Pivot Serration



d.
E223616E01
0.995,0.932 0.995,1.1 false 0.908,1.097 1.075,1.250 0.167,0.153 10 *1

Install the rear wiper arm and blade assembly with the nut to the position shown in the illustration.

Text in Illustration
*1 Ceramic Dot

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

HINT:

Hold the wiper arm by hand while tightening the nut.



e.

Turn the power switch on (IG).


f.

Operate the rear wiper while spraying washer fluid onto the back door glass. Make sure that the rear wiper functions properly and the wiper does not come into contact with the vehicle body.


g.

Lift the wiper arm twice after the wiper stops and check the wiper set position.


h.

Turn the power switch off.


Hide 85292A 4.INSTALL REAR WIPER ARM HEAD CAP

a.
E223601

Engage the 2 claws to install the rear wiper arm head cap as shown in the illustration.


b.
E223598

Engage the 2 claws to close the rear wiper arm head cap as shown in the illustration.


Hide 67750 5.INSTALL BACK DOOR TRIM BOARD ASSEMBLY

Hide 67938A 6.INSTALL BACK DOOR SIDE GARNISH LH

Hide 67937B 7.INSTALL BACK DOOR SIDE GARNISH RH

Hide 67939B 8.INSTALL BACK DOOR CENTER GARNISH