Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.03–2016.05
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B1244  Light Sensor Circuit Malfunction  


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) turns on or off the headlights and taillights according to the signal.

DTC No. DTC Detecting Condition Trouble Area
B1244
·

Malfunction in automatic light control sensor

·

Open or short in automatic light control sensor circuit


·

Automatic light control sensor

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E144299E55
0.542,2.635 0.76,2.781 0.219,0.146 10 false I1 0.521,2.813 2.531,2.979 2.01,0.167 10 false Automatic Light Control Sensor 4.865,2.792 6.75,3.135 1.885,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 4.865,2.635 5.135,2.802 0.271,0.167 10 false L7 1.583,0.823 1.979,0.979 0.396,0.156 10 false CLTB 1.583,2.167 1.979,2.323 0.396,0.156 10 false CLTS 1.583,1.5 1.979,1.656 0.396,0.156 10 false CLTE 2.063,0.917 2.219,1.094 0.156,0.177 10 false 3 2.063,2.25 2.219,2.396 0.156,0.146 10 false 4 2.063,1.594 2.219,1.74 0.156,0.146 10 false 6 5.031,0.813 5.427,0.969 0.396,0.156 10 false CLTB 5.031,1.458 5.427,1.615 0.396,0.156 10 false CLTE 5.031,2.156 5.427,2.313 0.396,0.156 10 false CLTS 4.802,0.917 4.99,1.063 0.188,0.146 10 false 20 4.802,1.573 5,1.719 0.198,0.146 10 false 22 4.792,2.25 4.99,2.396 0.198,0.146 10 false 21

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Illumination Rate Illumination rate information/0 ms to 2162.65 ms Value is output according to ambient light levels Value changes according to ambient light

OK:

Normal condition listed above is displayed.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
a.

Disconnect the I1 automatic light control sensor connector.


b.

Disconnect the L7 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L7-22 (CLTE) - I1-6 (CLTE) Always Below 1 Ω
L7-21 (CLTS) - I1-4 (CLTS) Always Below 1 Ω
L7-20 (CLTB) - I1-3 (CLTB) Always Below 1 Ω
L7-22 (CLTE) - Body ground Always 10 kΩ or higher
L7-21 (CLTS) - Body ground Always 10 kΩ or higher
L7-20 (CLTB) - Body ground Always 10 kΩ or higher




OK

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.
U155028E03
2.073,1.375 1.292,2.438 false 2.396,1.385 2.396,2.344 false 0.135,0.125 0.323,0.313 0.188,0.188 10 false *a 1.063,2.469 1.438,2.646 0.375,0.177 10 false CLTE 2.219,2.375 2.594,2.552 0.375,0.177 10 false CLTB 0.302,1.24 0.49,1.406 0.188,0.167 10 false L7

Reconnect the L7 main body ECU (multiplex network body ECU) connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L7-20 (CLTB) - L7-22 (CLTE) Power switch off Below 1 V
Power switch on (IG) 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
L7-22 (CLTE) - Body ground Always Below 1 Ω


Text in Illustration
*a Component with harness connected
(Main Body ECU (Multiplex Network Body ECU))



OK

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
a.
U155041E01
0.163,0.118 0.365,0.274 0.202,0.156 10 *a 0.484,2.499 0.874,2.643 0.390,0.144 10 CLTS 1.026,2.923 1.411,3.067 0.385,0.144 10 CLTE 1.588,2.391 1.259,2.883 false 1.588,2.258 0.977,2.565 false 0.521,1.653 0.680,1.843 0.158,0.190 10 I1

Reconnect the I1 automatic light control sensor connector.


b.

Connect an oscilloscope to the automatic light control sensor connector.

Text in Illustration
*a Component with harness connected
(Automatic Light Control Sensor)


c.
B113714E30
2.948,1.063 3.292,1.219 0.344,0.156 10 GND 1.844,1.177 1.969,1.333 0.125,0.156 10 A

Check the waveform.

OK:
Tester Connection Tool Setting Condition Specified Condition
I1-6 (CLTE) - I1-4 (CLTS) 5 V/DIV., 5 ms./DIV. Power switch on (IG), light control switch in AUTO position Correct waveform is as shown


HINT:

If the ambient light becomes brighter, width A becomes narrower.




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE AUTOMATIC LIGHT CONTROL SENSOR