Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.03–2014.11
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Parking Brake Switch Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) detects the condition of the parking brake switch assembly.

WIRING DIAGRAM

B242655E26
5.479,2.073 7.135,2.427 1.656,0.354 10 false Main Body ECU (Multiplex Network Body ECU) 4.281,1.063 5.938,1.427 1.656,0.365 10 false Instrument Panel Junction Block Assembly 0.958,1.094 3.052,1.375 2.094,0.281 10 false Parking Brake Switch Assembly 4.823,0.75 5.052,0.906 0.229,0.156 10 false 2C 4.833,0.531 5.01,0.688 0.177,0.156 10 false 20 5.76,0.656 5.938,0.813 0.177,0.156 10 false 12 5.99,0.729 6.302,0.875 0.313,0.146 10 false PKB 5.479,1.906 5.719,2.052 0.24,0.146 10 false MB 0.958,0.917 1.281,1.094 0.323,0.177 10 false A25 1.75,0.635 1.854,0.813 0.104,0.177 10 false 1

PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Data List.


e.

Read the display on the GTS.

Main Body
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch signal/ON or OFF ON: Parking brake switch on
OFF: Parking brake switch off
-

OK:

Normal conditions listed above are displayed.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
2.INSPECT PARKING BRAKE SWITCH ASSEMBLY
a.
E071372E15
1.573,0.573 1.917,0.729 0.344,0.156 10 false OFF 1.573,0.073 1.833,0.229 0.26,0.156 10 false ON

Remove the parking brake switch assembly (See page Brake>PARKING BRAKE>PARKING BRAKE SWITCH(for LHD)>REMOVAL for LHD, Brake>PARKING BRAKE>PARKING BRAKE SWITCH(for RHD)>REMOVAL for RHD).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - Switch body Shaft pushed in (OFF) 10 kΩ or higher
1 - Switch body Shaft not pushed in (ON) Below 1 Ω



Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C



A

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

B

REPLACE PARKING BRAKE SWITCH ASSEMBLY (for LHD)

C

REPLACE PARKING BRAKE SWITCH ASSEMBLY (for RHD)

3.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH ASSEMBLY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-1 - 2C-20 Always Below 1 Ω
A25-1 - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
U155052E02
0.164,0.16 0.364,0.347 0.200,0.187 10 *a 1.62,0.824 1.877,1.005 0.257,0.181 10 2C 1.614,2.99 1.878,3.171 0.264,0.181 10 MB 1.139,3.762 1.448,3.913 0.309,0.151 10 PKB 1.306,3.486 1.306,3.748 false

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-20 - MB-12 (PKB) Always Below 1 Ω
2C-20 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY