Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › 2012.03–2014.11
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM J

LIGHTING (EXT)  LIGHTING SYSTEM  Daytime Running Light Relay Circuit  


DESCRIPTION

The main body ECU (multiplex network body ECU) controls the daytime running lights.

WIRING DIAGRAM

E241415E03
0.386,0.918 1.255,1.298 0.869,0.381 10 from Auxiliary Battery 2.161,1.076 2.506,1.256 0.345,0.181 10 DRL 3.627,1.655 3.927,1.815 0.300,0.160 10 DRL 3.407,0.845 3.517,1.003 0.110,0.158 10 1 4.058,0.845 4.168,1.003 0.110,0.158 10 2 4.058,1.294 4.168,1.452 0.110,0.158 10 5 3.393,1.294 3.503,1.452 0.110,0.158 10 3 6.136,0.922 6.659,1.096 0.522,0.173 10 DRLE 5.703,4.422 6.941,4.956 1.239,0.533 10 Main Body ECU (Multiplex Network Body ECU) 2.005,2.906 2.264,3.066 0.259,0.161 10 C7 2.252,2.364 2.356,2.524 0.104,0.161 10 2 3.14,2.364 3.243,2.524 0.104,0.161 10 1 2.005,3.064 3.494,3.416 1.489,0.352 10 Front Turn Signal Light Assembly RH 1.991,4.622 2.250,4.782 0.259,0.161 10 C8 2.238,4.066 2.342,4.227 0.104,0.161 10 2 3.126,4.066 3.229,4.227 0.104,0.161 10 1 1.991,4.781 3.480,5.133 1.489,0.352 10 Front Turn Signal Light Assembly LH 5.898,0.831 6.100,0.983 0.202,0.151 10 15 5.707,4.277 5.949,4.428 0.242,0.151 10 L7

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Active Test.


e.

Check that the daytime running lights operate.

Main Body
Tester Display Test Part Control Range Diagnostic Note
Daytime Running Light Daytime running lights ON/OFF -

OK:

Daytime running lights illuminate.




OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT DRL RELAY
2.INSPECT DRL RELAY
a.
B416269E03
1.729,0.719 2,0.719 false 2.656,0.719 2.927,0.719 false 2.521,1.125 2.938,1.125 false 2.531,1.625 2.948,1.625 false 1.208,1.313 1.385,1.542 0.177,0.229 10 false 1 1.219,0.76 1.396,0.99 0.177,0.229 10 false 5 0.208,0.771 0.385,1 0.177,0.229 10 false 3 0.208,1.323 0.385,1.552 0.177,0.229 10 false 2 1.604,0.646 1.781,0.875 0.177,0.229 10 false 1 2.979,0.635 3.156,0.865 0.177,0.229 10 false 2 3,1.042 3.177,1.271 0.177,0.229 10 false 5 3,1.542 3.177,1.771 0.177,0.229 10 false 3

Remove the DRL relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Voltage is not applied between terminals 1 and 2 10 kΩ or higher
3 - 5 Voltage is applied between terminals 1 and 2 Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - DRL RELAY)

NG

REPLACE DRL RELAY

3.CHECK HARNESS AND CONNECTOR (AUXILIARY BATTERY - DRL RELAY)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Relay terminal 1 - Body ground Always 11 to 14 V
Relay terminal 3 - Body ground Always 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (DRL RELAY - MAIN BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (DRL RELAY - MAIN BODY ECU)
a.

Disconnect the L7 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 2 - L7-15 (DRLE) Always Below 1 Ω
L7-15 (DRLE) - Body ground Always 10 kΩ or higher




OK

5.CHECK HARNESS AND CONNECTOR (DRL RELAY - FRONT TURN SIGNAL LIGHT ASSEMBLY LH AND RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (DRL RELAY - FRONT TURN SIGNAL LIGHT ASSEMBLY LH AND RH)
a.

Disconnect the C7 front turn signal light assembly RH connector.


b.

Disconnect the C8 front turn signal light assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Relay terminal 5 - C7-1 Always Below 1 Ω
Relay terminal 5 - C8-1 Always Below 1 Ω
Relay terminal 5 - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR