Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM › from 2016.05
RM2070E _59 Vehicle Exterior _061953 LIGHTING (EXT) _0301908 LIGHTING SYSTEM C

LIGHTING (EXT)  LIGHTING SYSTEM  B2430  LED Headlight LH Circuit Malfunction  B2431  LED Headlight RH Circuit Malfunction  


DESCRIPTION

These DTCs are stored when the low beam headlights do not illuminate, or a malfunction is detected in the communication between the headlight assembly and main body ECU (multiplex network body ECU).

DTC No. DTC Detection Condition Trouble Area
B2430 LED headlight LH circuit malfunction
·

Light control ECU LH

·

Headlight unit LH

·

No. 1 integration relay

·

Harness or connector

·

Main body ECU (multiplex network body ECU)


B2431 LED headlight RH circuit malfunction
·

Light control ECU RH

·

Headlight unit RH

·

No. 1 integration relay

·

Harness or connector

·

Main body ECU (multiplex network body ECU)



WIRING DIAGRAM

E224348E10
5.479,6.771 7.125,7.156 1.646,0.385 10 false Main Body ECU (Multiplex Network Body ECU) 1.333,3.177 2.906,3.375 1.573,0.198 10 false No. 1 Integration Relay 1.667,4.99 3.219,5.198 1.552,0.208 10 false Headlight Assembly RH 3.427,0.844 3.625,0.99 0.198,0.146 10 false 9 3.375,1.031 3.635,1.177 0.26,0.146 10 false 1G 3.365,1.49 3.625,1.635 0.26,0.146 10 false 1G 3.375,2.469 3.635,2.615 0.26,0.146 10 false 1G 3.365,2.938 3.625,3.083 0.26,0.146 10 false 1G 3.365,1.948 3.573,2.094 0.208,0.146 10 false 1H 4.656,0.854 4.865,1 0.208,0.146 10 false 32 4.656,1.031 4.865,1.188 0.208,0.156 10 false 2C 3.396,2.281 3.604,2.427 0.208,0.146 10 false 22 2.896,1.49 3.281,1.677 0.385,0.188 10 false HLPL 2.865,1.948 3.281,2.125 0.417,0.177 10 false GND2 2.854,2.469 3.271,2.615 0.417,0.146 10 false GND1 2.854,2.938 3.271,3.083 0.417,0.146 10 false HLPR 3.427,1.302 3.531,1.448 0.104,0.146 10 false 2 3.427,1.76 3.531,1.906 0.104,0.146 10 false 3 3.438,2.729 3.542,2.875 0.104,0.146 10 false 1 0.656,0.729 0.917,0.875 0.26,0.146 10 false 1H 0.719,0.521 0.823,0.667 0.104,0.146 10 false 7 0.354,3.281 0.76,3.469 0.406,0.188 10 false P/I 2 0.073,3.813 0.958,4.375 0.885,0.563 10 false from Auxiliary Battery 6.24,1.021 6.656,1.229 0.417,0.208 10 false HRLY 6.25,4.542 6.719,4.729 0.469,0.188 10 false RLEW 6.25,6.438 6.698,6.677 0.448,0.24 10 false LLEW 5.948,0.854 6.156,1 0.208,0.146 10 false 15 4.552,1.365 6.167,1.781 1.615,0.417 10 false Instrument Panel Junction Block Assembly 0.99,4.333 1.167,4.531 0.177,0.198 10 false 6 1.146,4.344 1.281,4.5 0.135,0.156 10 false E 1.177,6.24 1.313,6.396 0.135,0.156 10 false E 3.917,4.229 4.01,4.375 0.094,0.146 10 false 3 3.646,4.229 3.875,4.375 0.229,0.146 10 false LO 3.635,6.125 3.865,6.271 0.229,0.146 10 false LO 3.469,4.448 3.885,4.594 0.417,0.146 10 false PPOS 3.448,6.354 3.865,6.5 0.417,0.146 10 false PPOS 2.135,3.781 2.854,3.979 0.719,0.198 10 false Low (LED) 2.135,5.708 2.885,5.979 0.75,0.271 10 false Low (LED) 1.667,4.865 2.323,5.021 0.656,0.156 10 false A86 1.74,6.917 3.292,7.125 1.552,0.208 10 false Headlight Assembly LH 1.74,6.76 2.115,6.917 0.375,0.156 10 false A84 1.906,4.354 3.073,4.552 1.167,0.198 10 false Light Control ECU 1.021,6.229 1.167,6.396 0.146,0.167 10 false 6 3.885,6.135 3.979,6.281 0.094,0.146 10 false 3 3.885,6.354 3.979,6.5 0.094,0.146 10 false 1 3.917,4.448 4.01,4.594 0.094,0.146 10 false 1 5.927,4.365 6.146,4.51 0.219,0.146 10 false 21 5.875,4.552 6.25,4.781 0.375,0.229 10 false L190 5.875,6.458 6.188,6.635 0.313,0.177 10 false L190 5.938,6.271 6.177,6.479 0.24,0.208 10 false 24 5.917,1.031 6.156,1.177 0.24,0.146 10 false MB 1.885,6.24 3.042,6.49 1.156,0.25 10 false Light Control ECU 0.958,0.74 1.365,0.896 0.406,0.156 10 false BATT 2.969,1.021 3.271,1.177 0.302,0.156 10 false HL4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

Result:
Result Proceed to
Both DTC B2430 and B2431 are not output. A
Both DTC B2430 and B2431 are output. B
DTC B2430 or B2431 is output. C




A

B

2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - AUXILIARY BATTERY AND BODY GROUND)

C

6.INSPECT HEADLIGHT ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - AUXILIARY BATTERY AND BODY GROUND)
a.

Disconnect the 1H No. 1 integration relay connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connector Condition Specified Condition
1H-7 (BATT) - Body ground Power switch off 11 to 14 V


Standard Resistance:
Tester Connection Condition Specified Condition
1H-3 (GND2) - Body ground Always Below 1 Ω



c.

Disconnect the 1G integration relay connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-22 (GND1) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the 2C instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1G-9 (HL4) - 2C-32 Always Below 1 Ω
1G-9 (HL4) - Body ground Always 10 kΩ or higher




OK

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.
U155050E01
0.164,0.16 0.364,0.347 0.200,0.187 10 *a 1.62,0.824 1.858,1.005 0.238,0.181 10 2C 1.599,2.99 1.903,3.171 0.304,0.181 10 MB 1.376,3.762 1.789,3.913 0.413,0.151 10 HRLY 1.594,3.486 1.594,3.748 false

Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2C-32 - MB-15 (HRLY) Always Below 1 Ω
2C-32 - Body ground Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Instrument Panel Junction Block Assembly)



OK

5.CHECK NO. 1 INTEGRATION RELAY

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

5.CHECK NO. 1 INTEGRATION RELAY
a.

Replace the No. 1 integration relay with a new or known good one (See page Power Source / Network>POWER DISTRIBUTION>INTEGRATION RELAY>REMOVAL).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 and B2431 are not output.




OK

END (NO. 1 INTEGRATION RELAY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

6.INSPECT HEADLIGHT ASSEMBLY
a.

Disconnect the A84 headlight assembly LH connector or the A86 headlight assembly RH connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (B2430)
Tester Connection Condition Specified Condition
A84-3 (LO) - Body ground Light control switch in head position 11 to 14 V

RH Side (B2431)
Tester Connection Condition Specified Condition
A86-3 (LO) - Body ground Light control switch in head position 11 to 14 V




OK

7.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - NO. 1 INTEGRATION RELAY)
7.INSPECT MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
a.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
LH Side (B2430)
Tester Connection Condition Specified Condition
A84-1 (PPOS) - Body ground Power switch on (IG) and light control switch in head position 11 to 14 V

RH Side (B2431)
Tester Connection Condition Specified Condition
A86-1 (PPOS) - Body ground Power switch on (IG) and light control switch in head position 11 to 14 V




OK

8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)

NG

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - BODY GROUND)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
A84-6 (E) - Body ground Always Below 1 Ω

RH Side (B2431)
Tester Connection Condition Specified Condition
A86-6 (E) - Body ground Always Below 1 Ω




OK

9.CHECK HEADLIGHT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HEADLIGHT ASSEMBLY
a.

Replace the headlight assembly with a new or known good one (See page Vehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY>REMOVAL).


b.

Check for DTCs (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B2430 or B2431 is not output.




OK

END (HEADLIGHT ASSEMBLY WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

10.CHECK HARNESS AND CONNECTOR (HEADLIGHT ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the 1G No. 1 integration relay connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
1G-2 (HLPL) - A84-3 (LO) Always Below 1 Ω
1G-2 (HLPL) - Body ground Always 10 kΩ or higher

RH Side (B2431)
Tester Connection Condition Specified Condition
1G-1 (HLPR) - A86-3 (LO) Always Below 1 Ω
1G-1 (HLPR) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - HEADLIGHT ASSEMBLY)
a.

Disconnect the L190 main body ECU (multiplex network body ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
LH Side (B2430)
Tester Connection Condition Specified Condition
L190-24 (LLEW) - A84-1 (PPOS) Always Below 1 Ω
L190-24 (LLEW) - Body ground Always 10 kΩ or higher

RH Side (B2431)
Tester Connection Condition Specified Condition
L190-21 (RLEW) - A86-1 (PPOS) Always Below 1 Ω
L190-21 (RLEW) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR