The main body ECU (multiplex network body ECU) controls the high beam headlights.
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
Check the operation of the low beam headlights.
Low beam headlights operate normally.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Main Body / Active Test.
Check that the high beam headlights illuminate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Head Light Hi | High beam headlights | ON/OFF | - |
High beam headlights illuminate.
OK
NG
Remove the DIM relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 3 - 5 | Voltage is not applied between terminals 1 and 2 | 10 kΩ or higher |
| 3 - 5 | Voltage is applied between terminals 1 and 2 | Below 1 Ω |
OK
NG
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 2 - Body ground | Power switch off | 11 to 14 V |
| Relay terminal 3 - Body ground | Power switch off | 11 to 14 V |
OK
NG
Disconnect the 2C instrument panel junction block assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 1 - 2C-22 | Always | Below 1 Ω |
| 2C-22 - Body ground | Always | 10 kΩ or higher |
OK
NG
Disconnect the A9*1 or A12*2 headlight assembly LH connector and the A38*1 or A41*2 headlight assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 5 - A9-2 (HI)*1 | Always | Below 1 Ω |
| Relay terminal 5 - A12-2 (HI)*2 | Always | Below 1 Ω |
| A9-2 (HI)*1 - Body ground | Always | 10 kΩ or higher |
| A12-2 (HI)*2 - Body ground | Always | 10 kΩ or higher |
| A9-1 (E)*1 - Body ground | Always | Below 1 Ω |
| A12-1 (E)*2 - Body ground | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Relay terminal 5 - A38-2 (HI)*1 | Always | Below 1 Ω |
| Relay terminal 5 - A41-2 (HI)*2 | Always | Below 1 Ω |
| A38-2 (HI)*1 - Body ground | Always | 10 kΩ or higher |
| A41-2 (HI)*2 - Body ground | Always | 10 kΩ or higher |
| A38-1 (E)*1 - Body ground | Always | Below 1 Ω |
| A41-1 (E)*2 - Body ground | Always | Below 1 Ω |
*1: for LED Headlight
*2: for Halogen Headlight
OK
NG
Remove the instrument panel junction block assembly (See page Power Source / Network>POWER DISTRIBUTION>MAIN BODY ECU>REMOVAL).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 2C-22 - MB-22 (DIM) | Always | Below 1 Ω |
| 2C-22 - Body ground | Always | 10 kΩ or higher |
| *a | Component without harness connected
(Instrument Panel Junction Block Assembly) |
OK
NG