1. PRECAUTION
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
75762A
2.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING
When installing the rear door front window frame moulding, heat the vehicle body and rear door front window frame moulding using a heat light.
| Item | Temperature |
|---|---|
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Do not heat the vehicle body or rear door front window frame moulding excessively.
Clean the vehicle body surface.
Using a heat light, heat the vehicle body surface.
Remove the double-sided tape from the vehicle body.
Wipe off any tape adhesive residue with cleaner.
Clean the rear door front window frame moulding (if reusing the rear door front window frame moulding).
Using a heat light, heat the rear door front window frame moulding.
Remove the double-sided tape from the rear door front window frame moulding.
Wipe off any tape adhesive residue with cleaner.
Apply new double-sided tape to the rear door front window frame moulding.
| *1 | Double-sided Tape (A) |
| *2 | Double-sided Tape (B) |
| *3 | Double-sided Tape (C) |
| Item | Dimension |
|---|---|
| A | 0.8 mm (0.0315 in.) |
| B | 1.2 mm (0.0472 in.) |
| C | 5.0 mm (0.197 in.) |
| D | 15.0 mm (0.591 in.) |
| E | 40.0 mm (1.57 in.) |
| F | 410.0 mm (1.35 ft.) |
| G | 450.0 mm (1.48 ft.) |
Install the rear door front window frame moulding.
| *1 | Double-sided Tape |
Using a heat light, heat the vehicle body and rear door front window frame moulding.
Remove the release paper from the face of the rear door front window frame moulding.
After removing the release paper, keep the exposed adhesive free from foreign matter.
Engage the clip and guide to install the rear door front window frame moulding.
75740
3.INSTALL REAR DOOR BELT MOULDING ASSEMBLY
68104
4.INSTALL REAR DOOR GLASS SUB-ASSEMBLY
67488C
5.INSTALL REAR DOOR REAR GUIDE SEAL
67408D
6.INSTALL REAR DOOR WINDOW GUIDE SUB-ASSEMBLY
68152C
7.INSTALL REAR DOOR GLASS RUN
67842E
8.INSTALL REAR DOOR SERVICE HOLE COVER
67628
9.INSTALL REAR DOOR TRIM BRACKET
67604
10.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY
74262
11.INSTALL REAR DOOR ARMREST COVER
12.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL
69284D
13.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG
14.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).
64995
15.INSTALL DECK FLOOR BOX RH
64993
16.INSTALL REAR DECK FLOOR BOX
58411A
17.INSTALL NO. 1 DECK BOARD
58412A
18.INSTALL NO. 2 DECK BOARD
58410B
19.INSTALL DECK BOARD ASSEMBLY
20.INITIALIZE POWER WINDOW CONTROL SYSTEM
21.INSPECT POWER WINDOW OPERATION